1 / 36

OSI Layer 1: Physical Layer

OSI Layer 1: Physical Layer. David Turton Conestoga College Institute of Technology & Advanced Learning http://www.conestogac.on.ca/~dturton Doon 1D17 x3610. OSI Layer 1 - Physical. Electrical connections & signaling Standard examples: Bit 0 is +2.5v Bit 1 is –2.5v

Antony
Download Presentation

OSI Layer 1: Physical Layer

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. OSI Layer 1: Physical Layer David Turton Conestoga College Institute of Technology & Advanced Learning http://www.conestogac.on.ca/~dturton Doon 1D17 x3610

  2. OSI Layer 1 - Physical • Electrical connections & signaling • Standard examples: • Bit 0 is +2.5v • Bit 1 is –2.5v • UTP standards, RJ45 pin-outs, etc. • Hardware: cable/media, hubs, repeaters

  3. Network Interface Card (NIC) Cabling or media Hub: Layer-1 device Switch: Layer-2 device Wireless networking: radio, infrared, satellite Wireless access point

  4. Coaxial Cable • Construction: • Copper core, insulation, metal shielding, insulating sheath • Good resistance to RFI & EMI interference • Older coaxial Ethernet cables: • 10base5 - Thick Ethernet (RG8) • 500M maximum length • Connector: vampire clamp & transceiver • 10base2 - Thin Ethernet (RG58) • 185M maximum length • Connector: BNC (British Naval Connector) • Coax is no longer used in networks • Mostly in cable TV (CATV) • RG-59 (ok) and RG-6 (better) grade cables RG: radio grade

  5. UTP Twisted-Pair Cable STP • 4 pairs of wires • Solid cores • Infrastructure: in walls & ceilings (don't move) • Cheaper, easier to connect, less signal attenuation • Stiffer – strains connections if used as patch cable • Max length (10/100baseT): 100M • Stranded cores • Patch cables: PC to wall jack, switch to BIX panel • More expensive, flexible (to route around desks) • Poorer electrical performance: • Max length (10/100baseT): 10-25M ? • Twists • Reduce cross-talk between pairs Foil shield Ground wire

  6. Cable Descriptorseg: 10baseT, 100baseT, 1000baseT, 10GbaseT • 10, 100, 1000 • Transmission speed in Mb/s (megabits per second) • 10 and 100 Mb/s – use 2 pair • 1,000Mb/s (1Gb/s) – uses 4 pair • 1000baseTX – 1Gb/s over 2 pair; defunct: required CAT6 • base • Baseband – one signal at a time on media • T • Twisted-pair (copper) • 100baseTX • Specific refinement of general 100baseT category

  7. Twisted-Pair gradesMHz – megahertz: millions of cycles per second • CAT 3 – 16Mb/s • 100M @ 10baseT • CAT 5 – 100MHz • 100M @ 100baseT • CAT 5e – 100MHz* • 100M @ 100baseT • <100M @ 1000baseT * • CAT 6 – 250MHz • 100M @ 1000baseT • 37-55M @ 10GbaseT • CAT 6e – 500Mhz • 100M @ 10GbaseT * Minimum CAT 5e standard is 100MHz, but manufacturers claim "tested to 350MHz"

  8. Twisted-Pair Connectors • RJ45 – networking (8 contact-points) • Shielded or unshielded • Metal jacket connects grounding wire on cable to switch/PC • Usually for solid or stranded cable … newer ones do both • Solid: v-shaped cutter • Stranded: plunge cutter • Also: • Pull-through (newer) or closed-ended (traditional) • Wire-guide insert (transition) • Note: • Use connector rated for the cable grade • CAT6 is thicker cable than CAT5e • But RJ45 external dimensions the same • Wire guides slightly offset, rather than side-by-side

  9. RJ45 Connectors Shielded RJ45 plug RJ45-to-RJ45 coupler Unshielded RJ45 plug Shielded, with strain relief Unshielded, no strain relief Unshielded RJ45 Keystone jack for wall outlet Shielded RJ45 Keystone jack

  10. BIX 100 punch-down block Mounted on a rack, RJ45 jacks on other face to connect to switch Keystone jack Punch-down tool to seat & trim wires Different cutters for 110 and Keystone Wall plate for Keystone jack

  11. Fire Rating(UL – Underwriters Laboratories) • Concerns: • Conducting fire through building & noxious fumes • UL1581 - General purpose: • Enclosed in walls or conduit (pipe) • UL910 - Plenum: • Horizontal in free-flowing air • Ducts, suspended ceilings • UL1666 - Riser: • Vertical in free-flowing air • Between floors

  12. RFI & EMIfibre-optic is immune, though expensive • RFI • Radio Frequency Interference • Short-wave, CB radios, microwaves • EMI • Electromagnetic Induction • Machinery, trucks/loaders, florescent lights • Both induce current (noise) in metal wires • Create errors in signals • Force re-transmissions, increasing traffic load

  13. STP vs UTPshielded or unshielded? • UTP • Unshielded twisted pair • Usually OK, but not around machinery • STP • Shielded twisted-pair • Metal foil inside plastic casing, sometimes around wire pairs • Grounded at one end (OK), or both ends (better) • Reduces or eliminates RFI & EMI • Ground loop - different grounds at ends • Creates a voltage in shield • Can heat wire and interfere with signal • Shield not grounded • It becomes an antenna

  14. Ground Loop Situation Switch in office here Cables are 60M long Buried in conduit, in tunnel across roadway, run beside machinery, 10Mb/s required now Used CAT 5E STP, direct-burial grade Grounds are likely to be at different potential Will cause voltage in shield  Causing interference Grounded one end, at switch or camera IP cameras here

  15. UTP/STP pin-out logicTerminating vs Communication Equipment • DTE – Data Terminating Equipment • Signal ends here, is not passed on • Hosts: computers, servers, printers & routers • DCE – Data Communication Equipment • Pass signals from one DTE device to another • Switches, hubs For 10baseT & 100baseT: • Pins 1 & 2 on DTE are transmit • Pins 1 & 2 on DCE are receive • I talk  you hear • Pins 3 & 6 on DTE are receive • Pins 3 & 6 on DCE are transmit • You talk  I hear receive green T568B transmit orange blue brown 1 2 3 4 5 6 7 8 It's almost as if the 3-6 pair is split to keep the other pairs away from each other

  16. MDI-X switch portsExtending networks by daisy-chaining switches • MDI - Medium Dependent Interface • Network interface on a PC • MDI-X • Network interface on a switch • Transmit/receive pins reversed • PC-to-switch connections • Use straight-through cables • Pin 1  pin1, pin 2  pin 2, etc. • Switch-to-switch extensions? • Use dedicated MDI-x or switched MDI/MDI-x port • Use a crossover cable( ): 13, 26, etc. • Most switches today detect & switch MDI-X to MDI • Can use a straight-through cable between switches 3rd floor PCs 2nd floor PCs 1st floor PCs servers

  17. Wiring Patterns • Straight-through: 11, 22, etc. • To connect DTE to DCE • Computer to switch • Crossover • To connect similar devices: • DTEDTE (computer to computer) • DCEDCE (switch to switch) • Rolled cable • Connect network port to serial port • Computer to router’s console port • Loopback • Connect your input pins to your output pins • To test your network card

  18. Wiring Standards • 568A & 568B • Pick a standard...and stay with it • Either will work • Patch cables are usually 568B • Same standard both ends: • Straight-through cable • 568A one end, 568B other: • 10/100baseT crossover oranges split around blues receive green T568B greens split around blues transmit orange blue brown 1 2 3 4 5 6 7 8

  19. Cross-Over Cablesused between similar devices:switch-to-switch, PC-to-PC, router-to-router • 10/100baseT – 2 pair used • 1  3 • 2  6 • 3  1 • 4  4 (unused) • 5  5 (unused) • 6  2 • 7  7 (unused) • 8  8 (unused) • 1000baseT – all 4 pair used • 1  3 • 2  6 • 3  1 • 4  7 • 5  8 • 6  2 • 7  4 • 8  5 • Or just use straight-through • And rely on auto-sense MDI/MDI-X

  20. Rollover Cable • Used to connect to serial console port on Cisco routers • So can use HyperTerminal to talk to it. • Use same 568A or 568B pin-out on both ends • Like a straight-though cable • Just have the tab up on one end, down on t’other

  21. Hardware Loopback10/100baseT simulation • PC sees own output as input • Used to test network card • When NIC has hardware diagnostics • RJ45 jack wired one pin to another • 1-3, 2-6

  22. Fibre-Optic Cables • Immune to RFI & EMI • Glass or plastic core, refractive cladding • 1 to 40km without repeaters • Expensive & difficult to install • Cut/polish ends exactly square, no splinters • Switch port or transceiver converts back to copper • Kink, sharp turn … it's broken • SMF – single-mode fibre-optic cable • High speed, long distance, one signal • MMF – multi-mode fibre-optic cable • Multiple signals • High speed, high bandwidth, medium distance

  23. Fibre-Optic Connectors Newer, smaller More connections in same space Transmit & receive fibres are in one connector Pre-terminated ends – easy to use Older, but Popular ST (straight tip) BNC-like connections Easy to connect Most popular MT-RJ • LC • Becoming more popular • fibre-channel to SANs • Gig Ethernet switches SC (square connector) Latch connector

  24. Physical Topologies Main LAN topologies: bus star ring

  25. Bus Topology • Common with coaxial cables • Max network length: 185M without repeaters • Cable goes from T-connector on one device • To T-connector on next device

  26. Bus Topology • All computers see all traffic • Only 1 message on network at a time • Only read in stuff addressed to them • Can modify interface to "sniff" traffic & snoop on others • Difficult to troubleshoot • Continuous line end-to-end • Need terminators (resistors) to stop "echo" • A break takes whole network down. • Not scalable • Break network to add/move a computer • Limits: number of devices, total cable length, bandwidth, collision/resend, etc.

  27. Star Topology • Devices connect to a central hub or switch • Using twisted-pair cables • Easier to troubleshoot: • One computer down: • Check hub port, cable, computer • All computers down • Check hub (single point of failure) • Scalable: • Just plug in another computer • Can daisy-chain additional hubs • Up to 100M host-to-hub • Hub is a repeater Hub Max 100M

  28. Ring Topology • Each computer connected to 2 neighbours • 2 cables per computer: ring in/ring out • Everyone "sees" everything… • No contention: • Can attain full rated speed • Adds, moves & cable faults • Take whole network down • Harder to troubleshoot • Common in WANs, not LANs • SONET has a backup ring to bypass faults

  29. Mesh Topology • Every device connects to every other device • n(n-1)/2 connections • Very fault-tolerant • Very expensive • Difficult to manage/maintain • Internet • Modified or hybrid mesh 4 hosts  6 connections Add one … 5 hosts  10 connections 6 hosts  15 connections

  30. Point-to-Point • Direct connection between two devices • Common on WAN links • Physical connection between routers • Logical connection in connection-oriented protocols (Frame Relay) WAN link between routers Cable/DSL/modem to ISP's router Ethernet, serial, parallel, wireless

  31. Point-to-Multipoint • One device to multiple devices • Dedicated connection to each remote device • Connections are all part of same network • Structure of Internet • Also as network backbone

  32. Hybrid Topologies • Combination of two or more topologies • Examples: • Star-bus: star configuration using a hub • Hubs have a shared bus between all the ports. • Star-ring: star configuration on a token-ring network • Point-to-point bridge connecting two star LAN segments

  33. Key point: TCO • Network's going to be there for 10 years or more • Ensure it is scalable • Computers will be added • Computers will be moved • Faster switches, faster PCs will be added • Cables are in walls & ceilings • Costly to replace or upgrade • Pray for dropped ceilings! • Ensure cables are rated for future speeds • And connectors…

  34. RepeaterHub  a multi-port repeater • Interprets and regenerates signals before they’re unintelligible • Voltage (signal strength) diminishes over distance (attenuation) • Interference induces noise (waveform damage) in signal • Doesn't just amplify the signal • That would not repair the waveform 10base2: 185M UTP: 100M Repeater Initial signal: +2.5v – bit 0 -2.5v – bit 1 Still readable, but just Regenerated: +2.5v – bit 0 -2.5v – bit 1

  35. Layer-1 Devices:Hubs & Repeaters

  36. Layer-1 Devices:Hubs & Repeaters • Used to extend LAN distance • Regenerate & forward signals, indiscriminately • They have an internal bus • All ports are connected together • Only one transmission is allowed at one time • 8 hosts on 10baseT or 10base2: • Average 1.2Mb/s per host • Can interpret between media • Convert from coax to UTP to fibre

More Related