1 / 103

Analog Fundamentals of the ECG Signal Chain

Analog Fundamentals of the ECG Signal Chain. Prepared by Matthew Hann , Texas Instruments Precision Analog Applications Manager. Objectives. Introduce Basic ECG Concepts Motivate the Need for TINA and SPICE Simulation for ECG Analysis

avanhoose
Download Presentation

Analog Fundamentals of the ECG Signal Chain

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Analog Fundamentals of the ECG Signal Chain Prepared by Matthew Hann, Texas Instruments Precision Analog Applications Manager

  2. Objectives • Introduce Basic ECG Concepts • Motivate the Need for TINA and SPICE Simulation for ECG Analysis • Introduce Discrete Analog Functions of the ECG Signal Chain • Motivate Need for Low Cost Integrated ECG Conditioning System • Introduce the ADS1298 and Its Embedded ECG Circuitry and Functions

  3. Analog Fundamentals of the ECG Signal Chain • What is a Biopotential? • What is ECG? • The Einthoven Triangle • Analog, Lead Definitions, Derivations, and Purpose • Modeling the Electrode Interface • Input Filtering and Defibrillation Protection • The INA front end • AC vs. DC coupling • RL Drive Amplifier Selection and Design • The ECG Shield Drive • Lead Off Detection • PACE Detection • INA post Gain + Analog Filtering • A/D Conversion Options and Filtering • ADS129x Introduction, Features, and Advantages

  4. What is a Biopotential?

  5. What is a BiopotentialAn electric potential measured between living cells

  6. What is a BiopotentialEvery cell is like a little battery

  7. What is a BiopotentialBiopotentials from cells electrodes

  8. What is ECG?

  9. What is ECG?A measure of the electrical activity of the heart

  10. What is ECG?ECG and blood pressure waves

  11. What is ECG?Actual ECG-normal

  12. What is ECG?ECG irregular tracings due to external artifacts

  13. What is ECG?Modeling the electrode interface Electrical characteristics include a DYNAMIC resistance, capacitance, and offset voltage

  14. Analog Lead Derivation

  15. Einthoven’s Law In electrocardiogram at any given instant the potential of any wave in Lead II is equal to the sum of the potentials in Lead I and III. Analog Lead DerivationECG Einthoven Triangle, 1907 3 Body Electrodes, 3 Derived Leads = I, II, III LEAD I = VLA-RL – VRA-RL LEAD II = VLL-RL – VRA-RL LEAD III =VLL-RL – VLA-RL Right Leg Reference, RL

  16. Analog Lead DerivationThe Wilson Central (WCT) Provides Chest Lead Reference at Center of Einthoven Triangle Assuming: RRA = RLA = RLL Then: *Drawing Taken From Bioelectromagnetism, Jaako Malmivuo and Robert Plonsey

  17. The Wilson Central is used to derive a reference potential for the Chest Leads, V1 – V6 Analog Lead DerivationThe Wilson Central is the AVERAGE potential between RA, LA, and LL RRA VOUT = V(1-6) - VWCT RLA RLL

  18. Different Chest Leads Provide: *Unique ECG Signature *Enhanced Pattern Recognition *Isoelectric Point @ V3-V4 Analog Lead DerivationChest Lead Signals Provide Different Information at Different Cross-Sectional Angles

  19. Analog Lead DerivationAugmented Leads Derived via WCT to Provide Enhanced Vector Information • Each lead provides unique information about the ECG Output Signal • Multiple Angles Give a Better Than 2-D Picture of the ECG Output • AVR, AVL, AVF derived via midpoint of 2 limbs (resistor divider) with Respect to 3rd limb

  20. Analog Lead DerivationIEC60601-2-51—Diagnostic Standards Electrodes Needed 1 Lead LA, RA 3 Lead LA, RA, LL 6 Leads LA, RA, LL 12 Leads LA, RA, LL, V1-6

  21. Left Axis Deviation (LAD) and = + Analog Lead DerivationDifferent Lead Combinations Reveal Axis Deviation QRS in AVF QRS in LEAD I Mean QRS Vector Points Toward Area of Infarction (Damage)

  22. Analog Lead DerivationDifferent Lead Combinations Reveal Axis Deviation I I AVF AVF I I AVF AVF

  23. ECG Input Filtering, Defibrillation Protection, and Isolation

  24. ECG Input Filtering and ProtectionExample: LEAD I Protection with Input Filtering CF, Ccm, and Cdiff + Rfilter form LPF Series Resistance Limits Input Current Protection Diodes +Vs Rfilter2 RPatient Rfilter1 LA CF CCM +Vs NE2H Zener Diode Cdiff -Vs Rfilter2 Rfilter1 RPatient RA CCM CF NE2H -Vs Patient Protection 10 -20k ohms Ne2H Lamps/TVS Protect Against Defibrillation Voltages Cdiff = 10 x Ccm

  25. System Block Diagram

  26. System Block Diagram INA Wilson MUX QRS and PACE Detect I dV/dt II RA III LA aVR LL aVL aVF RL Filter Isolation MUX WCT INA A/D V1 V2 DIO V3 V4 V5 V6

  27. The INA Front End

  28. The INA Front EndKey Features of the INA Front End *Important* Less Important • Input Bias Current • Input Impedance • Input Current Noise • Input Voltage Noise • Power Consumption • DC/AC CMRR • Input Offset Voltage • Input Offset Voltage Drift • Gain Error • Nonlinearity • PSRR *DC Errors such as VOS are swamped out by the Offsets Introduced by the Skin-Electrode Contacts

  29. The INA Front EndIdeal Simulation Circuit with Current and Voltage Noise Sources ECG + Skin Impedance Input CM + Differential Filtering Electrode Impedance + Offset Ideal INA Front End

  30. The INA Front EndSimulation Showing Output-Referred Total RMS Noise vs. Bandwidth (G = 1-10) Noise may NOT necessarily increase linearly with gain (INA or PGA topology dependent)

  31. The INA Front EndTINA Simulations Showing Output-Referred ECG Signal (G = 1-10) Snapshot of R Wave from ECG Waveform ECG Signal Varies LINEARLY with Increase in Gain

  32. The INA Front EndWhat is the MAX gain on the INA When Using a DC Removal Circuit? Integrator Removes Gained up DC offsets and servos INA output to Vref (3) Vref (2) (1) (1) Electrode Offset MAX = +/- 300mV (2) Swing of INA = V(+) – 50mV (3) Integrator Compliance = (ECGp + ECGn +VOS + VOSelectrode)* Gain < VCC - Vref

  33. The INA Front EndSimulation Circuit with Ideal INA and Vref = 2.5V as Integrator Input OPA333 Used as Integrator to Remove DC and Simulate Real Response During Saturation

  34. The INA Front EndECG + Integrator Output of INA vs. Gain for Vref = 2.5V As the output of the Integrator Saturates from Increased Gain, Vout of the INA pulls away from Vref

  35. The INA Front EndIf it is Advantageous to Maximize Gain with a Low Noise INA up Front, Why not AC Couple? ECGp VCM + ECGp + VOSelectrode1 (ECGp –ECGn)*Gain VCM + ECGn + VOSelectrode2 ECGn *AC Coupling Removes Electrode Offsets so that Higher Gain Can Be Used for Potentially Better SNR in the Signal Chain Path

  36. The INA Front EndTINA Simulation Circuit to Show AC-Coupled INA Gain Sweep

  37. The INA Front EndINA Gain = 1-1000 with VREF = 2.5V AC Coupled

  38. The INA Front EndWhat is CMRR? Why is it Important in ECG? ECGp VCM Lower CMRR = More Unwanted Output Signal ECGn

  39. The INA Front EndWhat is CMRR? Why is it Important in ECG? RP1 ECGp CC1 The INA includesthe R and C and must be considered in the overall CMRR Analysis VCM CC2 ECGn RP2 • Mismatch in Rp and Cc causes a differentialsignal error • Even a 1% tolerance on Cc cause a 20dB attenuation in CMRR

  40. The INA Front End50/60Hz Common Mode Simulation Circuit with 1µF Coupling Capacitors Mismatched CMR TINA Circuit Test By Sweep of Mismatch of Input Coupling Capacitors

  41. .5% Mismatch 0% Mismatch The INA Front EndPlot of CMRR vs. Frequency for .01 - .5% Coupling Capacitor Mismatch

  42. The INA Front EndPlot of ECG Response to 5Hz CM Input Signal (0%-.5%) CC Mismatch Lower Frequency Signals Couple Directly Into the ECG Signal to the Output

  43. The INA Front EndPlot of ECG Response to 50/60 Hz CM Input Signal • 50/60Hz Noise Rejection is Virtually Unaffected by AC Coupling • Dependent Primarily on the Noise Magnitude and the CMRR of the Front End INA

  44. The Right Leg Drive Amplifier

  45. The RL Drive AmplifierThe RL Drive Amplifier Serves 2 Purposes: (1) Common Mode Bias (2) Noise Cancellation ECGp CMnoise CMnoise ECGn Average VCM is Inverted and Fed Back to RL; Cancels 50/60Hz noise *Tapping off center of split gain resistor feeds the following voltage to the RL Drive Circuit [(Vcm+ ECGP )+ (Vcm+ ECGn )]/ 2 = Vcm + (ECGp + ECGn )/2

  46. The RL Drive Amplifier Simulation Circuit for Response to 50/60 Hz CM Noise Injection Source = Included for TINA spice Convergence

  47. The RL Drive Amplifier TINA Simulation with NO RL Drive; CM Noise is Coupled to Output

  48. The RL Drive Amplifier TINA Simulation with RL Drive; Output Noise is Reduced

  49. The RL Drive Amplifier Analyzing the RLD Amplifier Loop VECGp + Vep + VCM ECGp Vep RA RG/2 RG/2 RA • More Gain = Better CMRR • Loop Corrects for Electrode Offset, VOSA1, and VOSRLD RF Ven ECGn VREF RI VECGn + Ven + VCM

  50. The RL Drive Amplifier Simulation Circuit for CMRR of RLD Loop Sweep Feedback Resistor Gain to show Effects of CMRR @ 50/60Hz

More Related