1 / 20

ACETITE ADHESIVES in LCD Applications

ACETITE ADHESIVES in LCD Applications. Toshiharu Noguchi Technical Manager Asec Co., Ltd. November 30, 2003. Mother Glass Bonding : UV (Temporary) Main Sealing : Heat-cure Epoxy → UV End Sealing : UV/Visible Light Cure Terminal Sealing (Reinforcement) TAB : Silicone → UV

avedis
Download Presentation

ACETITE ADHESIVES in LCD Applications

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ACETITE ADHESIVES in LCD Applications Toshiharu Noguchi Technical Manager Asec Co., Ltd. November 30, 2003

  2. Mother Glass Bonding : UV (Temporary) Main Sealing : Heat-cure Epoxy → UV End Sealing : UV/Visible Light Cure Terminal Sealing (Reinforcement) TAB : Silicone → UV Clip Pin : UV FPC : UV Terminal Bonding (ACP): Heat-cure Epoxy → UV COG/ITO Coating : Silicone → UV Types Of Adhesives in LCD Application

  3. Adhesives in LCD Application

  4. Major Advantages of UV or UV/Visible Light Curable Adhesives: • Fast Cure → Reduction of Assembly Time • Solvent Free → Environmental friendly • One Component → Production Efficiency ↓ Total Cost Saving

  5. Main Sealing 400~1,000mm Glass Bonding 400~1,000mm MOTHER GLASS BONDING - 1 Processes: 1) Apply Main-Sealing Adhesive 2) Apply Mother Glass Bonding Adhesive 3) Align and mate Glasses 4) UV Light Exposure 5) Pressing and Heat curing

  6. MOTHER GLASS BONDING - 2 Requirements for Adhesive: • Non-Flow Viscosity • Easy Spread in Small Gap • Hot Strength (No movement during Heating) AS-6954 (20,000mPa-s, Thixo 4)

  7. END SEALING - 1 End Sealing Processes 1) Suck LC into Cell 2) Wipe excess LC around the Charging Port 3) Apply and Suck-In Adhesive (by Cooling Method or Press Method) 4) UV Light Exposure

  8. COOLING Method STEP 1: Filling LC into Cell STEP 2: WIPING OFF Excess LC STEP 3: Applying UV Adhesive STEP 4: Cooling Cell down to 10-15deg.C STEP 5: Curing by UV Radiation PRESS Method STEP 1: Filling LC into Cell STEP 2: Stacking 20-60 Cells STEP 3: Pressing STEP 4: WIPING OFF Excess LC STEP 5: Applying UV Adhesive STEP 6: Releasing Press slightly STEP 7: Curing by UV Radiation Sealing Process Details END SEALING - 2

  9. 4) 2) 3) 1) LC END SEALING - 3 Main Problems In End Seal: 1) LC Disordering: Color difference / Contrast 2) Occurrence of Irregular shapes(“HIKE”) at Neck Region: Poor Appearance & LC Leakage 3) Gaps between End Seal & MainSeal: LC Leakage 4) Debonding of End Seal: LC Leakage

  10. END SEALING - 4 Requirements of End Sealant • Good Compatibility with LC (Low Extractive Ionic Compounds) • Good Adhesion to substrates (LC wetted) • Low UV Energy Curability (500~1,000mJ/cm2) (High CTV → Visible Light Curability) • Resistance to Washing agent • Durability • Appropriate Viscosity AS-1202 (6,000mPa-s) AS-1010 (10,000mPa-s) AS-1203 (20,000mPa-s)

  11. UV Adhesive TAB ACF UV Adhesive FPC ACF TERMINAL SEALING - 1 Application • Clip Pin: TN (Segment Type) • FPC, TAB: STN, TFT Process 1) Dispensing Process: One-sided or Two-sided a) Roller Method b) Syringe Method 2) UV Light Curing Process

  12. Terminal Sealing - 2 Requirements of Terminal Sealant • Good Adhesion to Glass, ITO, Sn, PI • Flexibility (Low Stress) • Moisture Resistance • Durability to withstand Thermal Shock & Thermal Aging • High Temp. resistance (Pin Clip) • Cure Depth > 1.0mm (Pin Clip) • Appropriate Viscosity AS-2002 (5,000mPa-s) AS-1057 (9,000mPa-s) AS-1204 (20,000mPa-s)

  13. FPC Au coated sphere Cu Pattern ACP ITO Pattern Glass TERMINAL BONDING - 1 Application • FPC to Glass (ITO, Conductive) Process 1) Apply ACP on ITO Terminal Pattern 2) Put FPC on the ITO Terminals 3) UV Light Exposure with Pressing

  14. TERMINAL BONDING - 2 ACP • UV Adhesive + Conductive Particles • Particles • Au coated Sphere Resin • Diameter: 3 ~ 5μm Requirements of UV Adhesive • Good Adhesion to Glass, ITO, FPC • Appropriate Flexibility • Appropriate Cure Shrinkage (Pressing Force) • Moisture Resistance and Durability • Appropriate Viscosity AS-2002 (5,000mPa-s)

  15. Overcoat Resin IC Chip FPC ACF or ACP COG/ITO OVERCOATING - 1 Processes: 1) Mount IC Chip on Glass (ITO Circuit) 2) Heat-Pressing 3) FPC Bonding with ACF or ACP 4) Apply COG Overcoat Resin over IC and ITO Pattern 5) UV Light Exposure

  16. COG/ITO OVERCOATING - 2 CURRENT PROCESS Bottle Neck 1) Insufficient Moisture Protection capability with RTV Silicone 2) Low Productivity due to Long Curing Time with RTV Silicone UV Curing Adhesives

  17. COG/ITO OVERCOATING - 3 Requirements of COG OVERCOATING RESIN • Low Water Permeability • Not Corrosive • Low Stress (Low Shrinkageor High Flexibility) • Toughness • Good Wettability (Glass, ITO, PI, Si) • Adequate Low Viscosity (< 1,000mPa-s) • Fast Cure (< 1,000mJ/cm2) • Durability (Thermal Shock, Heat Aging) AS-2008 (600mPa-s)

  18. Appendix LIGHT SHIELD RESIN - 1 Application 1) Protect IC of COG from Malfunction by Light 2) Apply the opposite side of Glass IC mounted 3) Current Process: Al or Black Adhesive Tape Overcoat Resin IC Chip FPC ACF or ACP Light Shield Tape or Resin

  19. LIGHT SHIELD RESIN - 2 Requirements of LIGHT SHIELD RESIN • UV/Visible Light Opaque (Black, White or Silver) • Screen Printable (High Productivity) • Good Adhesion to Glass • Adequate Low Viscosity (< 1,000mPa-s) • Fast Cure (< 1,000mJ/cm2) • Durability EX03-133 (6,000mPa-s)

  20. We can support you everywhere and every time directly! Thank you !

More Related