1 / 39

Team Assignments

Team Assignments. A Clayten Greenwell Elliot Magoto Jonathan Morgan Lisa Woosley B Joshua Cecil Zachary Rabold Richard Smith Robert Talley C Ryan Franklin Anthony Stegman Zachary Stucker Joshua Von Schlutter D Christian Pendleton Nathan Piersma Matthew Rogers

denna
Download Presentation

Team Assignments

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Team Assignments • A • Clayten Greenwell • Elliot Magoto • Jonathan Morgan • Lisa Woosley • B • Joshua Cecil • Zachary Rabold • Richard Smith • Robert Talley • C • Ryan Franklin • Anthony Stegman • Zachary Stucker • Joshua Von Schlutter • D • Christian Pendleton • Nathan Piersma • Matthew Rogers • Hayden Smith

  2. Team Assignments • E • Christopher Collins • Mark Lacy • Adam Leach • Daniel Rehner • F • Cory Boughey • Matthew Broaddus • Cory Henon • Stephen Howell • G • Christopher Allison • Brett Blanchard • Travis Greenwell • Samantha Thomas

  3. CE403 Construction Methodology Earthwork Fundamentals

  4. LEARNING OBJECTIVES • Define the common Soil Properties and how to determine each. • Define Soil-Volume Changes that occur during earthmoving operations. • Define Swell, and Shrinkage, and how to determine the Load & Shrinkage Factors. • Define Angle of Repose for common Soil Materials. • Describe the two common Soil Classification Systems and Basic Definitions.

  5. Soil Properties • Any mass of soil consists of solid particles with voids in between. • Soil solids are small grains of different minerals • Voids can be filled with either water or air

  6. Soil Properties • Total volume of the soil mass, Vt, consists of volume of soil solids, Vs, and the volume of voids, Vv • The volume of the Voids, Vv, consists of volume of water, Vw, and the volume of air, Va

  7. Soil Properties • We can schematically represent these three phases in a phase diagram. Volume Mass

  8. Soil Properties • Three volumetric ratios • Void ratio: • Normally expressed as a decimal • Max range of e is between 0 and infinity • Typical values: Sand (0.4 to 1.0); Clays (0.3 to 1.5)

  9. Soil Properties • Three volumetric ratios • Porosity • Normally expressed as a decimal • Max range of n is between 0 and 100%

  10. Soil Properties • Three volumetric ratios • Degree of Saturation • The degree of saturation tells us what percentage of the total volume of voids contains water • If soil is completely dry, S=0. If the pores are completely filled with water, S=100%

  11. Soil Properties • Mass relationships • Water (moisture) content: • Can range from zero (dry soil) to several hundred percent • Water content for most soils is well under 100%, although it can range up to 500% or higher in some marine and organic soils

  12. Soil Properties • Mass relationships • Total density: • Magnitude will depend on amount of water in the voids and density of the mineral grains • Typical values for most soils range from 1000 to 2400 kg/m3

  13. Soil Properties • Mass relationships • Solid density: • Typical values for most soils range from 2500 to 2800 kg/m3 (2.65 Mg/m3) • Dry Density:

  14. Soil Properties • Mass relationships • Density of Water: • The density of water varies slightly, depending on the temperature. • For most engineering work, it is sufficiently accurate to estimate pw=1000kg/m3=62.4lb/ft3

  15. Common Soil Properties

  16. Example Problem Given the Following: Vs=65 cm3, Vw=25 cm3, Va=10cm3 Ms = 175g, Mw=25g Find: Total Density, dry density, moisture content, void ratio, saturation, and porosity of the soil sample

  17. Soil Volume-Change Characteristics Bank Volume - (BCY) • Material is in natural state before disturbance Loose Volume - (LCY) • Material has been excavated or loaded. Compacted Volume - (CCY) • Material after compaction.

  18. Soil Volume-Change Characteristics

  19. Swell • A soil increases in volume when it is excavated because the soil grains are loosened during excavation and air fills the void spaces created.

  20. Shrinkage • When soil is compacted, air is forced out of void spaces. • The soil will occupy less volume than it did under either bank or loose conditions.

  21. Load Factor

  22. Shrinkage Factor

  23. Soil Weight & Volume Change Characteristics

  24. Load & Shrinkage Example Problem A soil weighs 1,960 lb/LCY, 2,800 lb/BCY and 3,500 lb/CCY. b. How many BCY & CCY are contained in 1,000,000 LCY? Bank Volume 1,000,000 LCY x 1,960/2,800(BCY/LCY) = = 1,000,000 LCY x 0.70(BCY/LCY) = 700,000 BCY Compacted Volume 1,000,000 LCY x 1,960/3,500 (CCY/LCY)= or = 700,000 BCY x 0.80 (CCY/BCY) = 560,000 CCY

  25. Unified Soil Classification System • Two Letter System • Symbols to represent soil type: Symbol Soil Type G Gravel S Sand M Silt C Clay Pt Highly organic soil and peat. • Symbols to represent index properties W Well-graded (for grain-size distribution) P Poorly-graded (for grain-size distribution) L Low to medium plasticity H High plasticity

  26. Angle of Repose • The angle that the sides of a spoil bank or pile naturally form with the horizontal when the excavated soil is dumped onto a pile. • The angle varies with the soil’s physical characteristics and its moisture content.

  27. Materials & Angle of Repose Clay 35° Common Earth, Dry 32° Common Earth, Moist 37° Gravel 35° Sand, Dry 25° Sand, Moist 37°

  28. H D Spoil Pile Dumped from a single fixed point Volume =1/3 Base Area x Height

  29. Soil Identification & Classification

  30. Basic Definitions • The liquid limit (LL) is the water content (%) at which the soil will just start to flow when subjected to standard shaking test. (Casagrande Test) • The plastic limit is the moisture content (%) at which the soil just begins to crumble when rolled into a thread 1/4” in diameter. • The plastic index is the numerical difference between the liquid and plastic limits and represents the range in moisture content over which the soil remains plastic.

  31. Unified Soil Classification System • Two Letter System • Symbols to represent soil type: Symbol Soil Type G Gravel S Sand M Silt C Clay Pt Highly organic soil and peat. • Symbols to represent index properties W Well-graded (for grain-size distribution) P Poorly-graded (for grain-size distribution) L Low to medium plasticity H High plasticity

  32. AASHTO Soil Classification System • American Association of State Highway and Transportation Officials • A-1 through A-7 • Table 2-3, Page 25.

  33. Construction Characteristics of Soils • Drainage • Construction Workability • Suitability for Subgrade • Suitability for Surfacing

More Related