1 / 12

COM-ET10-T

COM-ET10-T. POWER. LINK. ACT. SD. RD. COM-ET10-T. The Cheops Ethernet-Module for the FX-Series. Functions. One TCP/IP Port to connect one remote Node. This could be for example : > GX (IEC) Developer > MX Components > MX Scada 32 and so on

huhn
Download Presentation

COM-ET10-T

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. COM-ET10-T POWER LINK ACT SD RD COM-ET10-T The Cheops Ethernet-Module for the FX-Series

  2. Functions • One TCP/IP Port to connect one remote Node. This could be for example : > GX (IEC) Developer > MX Components > MX Scada 32 and so on • One UDP/IP Port for FX to FX Communication! This is an UDP/IP Broadcast Communication for max 16 Stations with each one block Data a 32 Byte (or 8 Stations with each 64 Byte Data) !

  3. ET10-T POWER MITSUBISHI LINK CNV-BD ACT SD RD MELSEC FX1N(C) FX2N(C) Initial Processing The Initial Processing is done by the PLC program. The Parameter have to be stored in D-Register. These registers could start at a variable 1000th range. (This could be for example D0, D1000, D2000, ... ) !

  4. Parameter 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Module ID IP Address Subnet Mask Gateway IP UDP Port No TCP Port No 1 TCP Port No 2 Network No Station No Block Count Block Start Block All D1000 : 45 54 31 30 (ASCII : ET10) D1002 : 192.168.001.010 D1004 : 255.255.255.000 D1006 : 000.000.000.000 D1008 : 1024 D1009 : 1025 D1010 : 1026 D1011 : Network number D1012 : Station number D1013 : No of blocks this PLC D1014 : 100 (dec) = Start address D1015 : No of blocks all PLC’s hex dec dec dec dec dec dec 1 - 64 0 - 15 1 - 8 D100 2 - 16

  5. TCP/IP Port for Communication to a PC FXnN(C) - Hardware FX2NC und FX0N do not need a CNV-BD Board Personal Computer with a Virtual Serial Port Software ! COM-ET10-T CNV-BD Board FXnN RJ45 Interface Ethernet Network card Twisted Pair Cable ( cross cable)

  6. TCP/IP Port for Communication to a PC Communication format : Special Register D8120 = H81 Module ID 45=E; 54=T; 31=1; 30=0 PLC Program to set the ET10-T Parameter Module IP Address 192.168.001.010 Subnet Mask 255.255.255.000 Gateway IP Address 000.000.000.000 UDP Port Number 1024 TCP Port Number 1 1025 TCP Port Number 2 1026

  7. TCP/IP Port for Communication to a PC Tibbo “Device Server Toolkit (TDST)” software ! Settings in the Virtual Serial Port Software Free download at: http://www.tibbo.com/

  8. TCP/IP Port for Communication to a PC Choose a free COM Port number ! Disable this Check Box : Send „On-the-Fly“ serial commands Choose the TCP / IP Protocol ! Set the IP-Address and Port-Number according to the settings for the COM-ET10 module in the PLC program !

  9. TCP/IP Port for Communication to a PC GX Developer GX IEC Developer Select now the new virtual COM Port 5 in the GX (IEC) Developer Transfer Setup !

  10. FXnN UDP/IP Port for FX to FX Ethernet Broadcast Communication FXnN(C) - Hardware FXnN(C) - Hardware PLC 1 : FX1N(C) Station No. : 0 IP-Address : 192.168.1.10 UDP Port : 1024 2 Blocks : 32 Words Data PLC 2 : FX2N(C) Station No. : 2 IP-Address : 192.168.1.12 UDP Port : 1024 2 Blocks : 32 Words Data FXnN COM-ET10-T RJ45 Interface CNV-BD Board Twisted Pair Cable ( cross cable )

  11. UDP/IP Port for FX to FX Communication PLC 1 Station No. 0 Network No 1 00 01 hex Station No 0 00 00 hex No of data blocks 2 00 02 hex PLC program to set the FX to FX Parameter Start device address D100 K100 No of blocks all PLC’s 4 00 04 hex Specify user data

  12. UDP/IP Port for FX to FX Communication PLC 2 Station No. 2 Network No 1 00 01 hex Station No 0 00 02 hex No of data blocks 2 00 02 hex PLC program to set the FX to FX Parameter Start device address D100 K100 No of blocks all PLC’s 4 00 04 hex Specify user data

More Related