1 / 17

Class A Foam 101

Class A Foam 101. Marysville Division of Fire 2009. Class A vs. Class B Foam. Class B Foam is repelled by hydrocarbons - Oleophobic Class A Foam likes hydrocarbons - Oleophillic . Class A Foam. Contains surfactants which decrease surface tension of water

matteo
Download Presentation

Class A Foam 101

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Class A Foam 101 Marysville Division of Fire 2009

  2. Class A vs. Class B Foam • Class B Foam is repelled by hydrocarbons - Oleophobic • Class A Foam likes hydrocarbons - Oleophillic

  3. Class A Foam • Contains surfactants which decrease surface tension of water • Contains emulsifiers which enhance “stickiness” to organic molecules • Similar to Class B foam in that it contains ingredients which make tiny bubbles • Biodegradable

  4. What is surface tension? • Force which makes water bead up • Surfactants decrease surface tension • Reduction of surface tension allows the water to spread out more on a surface and more likely to soak into that surface. • Increases moisture content • Decreases the temperature

  5. What does an emulsifier do? • Emulsifiers (in foam) bind with hydrocarbon fuels and work to break them down into smaller droplets and encapsulate them. So, when a Class A fuel burns, the emulsifier binds with the burnt surface.

  6. Advantages of Class A Foam • Spreads out and soaks into fuels • Binds with fuel • Covers the fuel with a cooling blanket • “Sticky Water”

  7. Why don’t we use Class A foam on gasoline too? • Class A foam does not work well on liquids that have polar solvents. (i.e. ethanol)

  8. Proportioning • Class A foam is typically proportioned from 0.3% to 1%. • Our default will be to initiate at 0.5% and titrate to desired effect up to 1%.

  9. Class A Parameters • Useable from 20o to 120o F, with freezing at 6o • 20 Yr shelf life if stored in sealed container, 1 yr if stored in apparatus reservoir tank. • Avoid mixing with Class B foam, it congeals into a sludge.

  10. Class A Foam uses • Class A foam has been used for years on initial attack, overhaul and exposure protection. • Permeates voids and cavities • Increases moisture content

  11. Hale Foam System • Hale Foam Logix System • 30 gallon Class A Foam Concentrate • Default at 0.5% foam at 150 GPM

  12. Hale Foam System • Red Button: On/Off • When turned “on” a red light will come on the bar graph under the numerical display

  13. Hale Foam System • “I” Button: Mode button. Switch between flow, %, total flow and total foam

  14. Hale Foam System • ↓ and ↑ button: change foam percentage We will default at .5%, but can be increased for deep seated fires or increased effect.

  15. Hale Foam System • If the display reads “0” or “Lo A”, the concentrate is nearing empty or is empty

  16. Hale Foam System • When done with the foam: • Turn off (red button (light goes out)) • Flush the hose line until only water come out • Reload hose and refill Class A Foam tank

  17. Questions? • Based on NFPA 1145, Use of Class A Foam in Manual Structural Firefighting, 2006 Edition

More Related