1 / 20

Announcements

Announcements. Assignment 1 due now. Assignment 2 posted, due on Thursday. Lecture 7 Overview. Filters Transient Circuits. Low pass filter. RC low-pass filter: preserves lower frequencies, attenuates frequencies above the cutoff frequency ω 0 =1/RC. For voltage. For power.

oksana
Download Presentation

Announcements

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Announcements • Assignment 1 due now. • Assignment 2 posted, due on Thursday

  2. Lecture 7 Overview • Filters • Transient Circuits

  3. Low pass filter • RC low-pass filter: preserves lower frequencies, attenuates frequencies above the cutoff frequency ω0=1/RC.

  4. For voltage For power Low pass filter Break frequency ω=ω0=1/RC, HV=1/√2 N.B. decibels:

  5. Build other filters by combining impedance response

  6. Which of the following is a low-pass filter? What happens to the output voltage when ω→0 (DC condition)? Answer: (c)

  7. Which of the following are high-pass or low-pass filters? Answers: (b) and (c) are high-pass; (a) and (d) are low-pass

  8. L C RLC Band-pass filters Measuring voltage output signal over R, Vr Low frequencies, C open, L shorted, Vr minimum High frequency, C shorted, L open, Vr minimum so, at high and low frequencies, see an open circuit - Vr minimum

  9. Band-stop (Notch) filters Measuring voltage output signal over L and C Low frequencies, C open, L shorted, Vlc maximum High frequency, C shorted, L open, Vlcmaximum so, at high and low frequencies, see an open circuit - Vlc maximum

  10. Another Example: Measuring voltage output signal over L and C, but this time in parallel (i.e. at high and low frequencies, see a short - V0=0)

  11. Transient Circuits

  12. Boundary condition: at t=0, vC(t)=0 so: Charging a capacitor During Charging (left-hand loop): Integrate both sides using: Gives:

  13. Charging a capacitor Solution is only true for that particular circuit (Voltage source plus resistor), but more complicated circuits can be reduced to this using Thevenin's Theorem Time constant τ=RC. Time needed to charge capacitor to 63% of full charge Larger RC means the capacitor takes longer to charge Larger R implies smaller current flow The larger C is, the more charge the capacitor can hold.

  14. Discharging a capacitor Charged Begin discharging Time constant τ=RC. Time needed for capacitor to drop to 37% of full charge Current flows in the opposite direction to charging Larger RC means the capacitor takes longer to discharge file:///Users/jholder/teaching/phys645/2011/rc/rc.html http://www.phy.ntnu.edu.tw/ntnujava/viewtopic.php?t=48

  15. Charging Capacitors Which configuration has the largest final charge on the capacitor? Answer: both the same (no current flow means no voltage drop across resistors)

  16. Charging Capacitors Which capacitor charges fastest? Answer: b)

  17. Time response of Inductors Switch to position a: Integrate and apply boundary condition t=0, i=0 Time constant τ=L/R. Talk about "Charging a capacitor" "Current build-up" in an inductor Switch to position b:

  18. Time response of Inductors A battery is connected to an inductor. When the switch is opened does the light bulb: 1.Remain off 2.Go off 3. Slowly Dim out 4. Keep burning as brightly as it did before the switch was opened 5. Flare up brightly, then dim and go out Answer 5

  19. Why care about Transient Analysis?not everything is a sine wave.... • Time dependence is very useful for some applications (e.g. making a clock) • Also becomes important in digital applications • Transient: refers to transition region between two states. • e.g. at the edges of a square wave

  20. Ideal Realistic Transient Analysis • Transistors are used as switches in digital circuits • Gate input used to control switching • Physical construction of transistors leads to "Capacitor Effect" • Switching is not instantaneous • Delay determined by RC time constant

More Related