1 / 24

IEEE802.16d Simulator WirelessMAN-OFDM-PHY layer

IEEE802.16d Simulator WirelessMAN-OFDM-PHY layer. Rev-s3 24 Sept 2004. Mohamad Charafeddine. Introduction. The Matlab’s Simulink simulation work is for the broadband wireless standard IEEE802.16d [and subsequently for the IEEE802.16-2004 once it is published]

susane
Download Presentation

IEEE802.16d Simulator WirelessMAN-OFDM-PHY layer

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. IEEE802.16dSimulatorWirelessMAN-OFDM-PHY layer Rev-s3 24 Sept 2004 Mohamad Charafeddine

  2. Introduction • The Matlab’s Simulink simulation work is for the broadband wireless standard IEEE802.16d [and subsequently for the IEEE802.16-2004 once it is published] • Currently the mandatory channel coding scheme is used (Reed-Solomon/ convolutional code), 16-QAM modulation, RS(64,48,8), CC rate=2/3 • A state machine can be implemented on top of the current model to take into account adaptive rate modulation.

  3. IEEE802.16d, WirelessMAN-OFDM 256-FFT, 16-QAM

  4. Randomization • PRBS generator: 1 + x14 + x15 • On DL: the scrambler is re-initialized at start of each frame with the vector: 100101010000000

  5. Concatenated Reed-Solomon / convolutional code (RS-CC)

  6. Reed-Solomon coding • Tail byte appended at end of the scrambled data • For the 16-QAM mode selected, RS(64,48,8) is used, with: • A primitive GF polynomial of: p(x) = x8 + x4 + x3 + x2 + 1 • And a code generator polynomial of:g(x)=(x+λ0) (x+λ1) (x+λ2).. (x+λ2T-1), λ=02Hex

  7. Convolutional Coding & Puncturing • Convolutional coding with a native rate of ½ • Constraint length of 7 • Generated with the following 2 generator polynomials: • G1=171oct=1111001 For X • G2=133oct=1011011 For Y • Puncturing of 4/3: X1Y1Y2; thus overall CC rate of ½*4/3 = 2/3

  8. 2-steps Interleaver (I) • Define: • Ncpc the number of coded bits per carrier (i.e. 2,4,6 for QPSK, 16QAM, 64QAM respectively) • s = Ncpc/2 • k: the index of the coded bit before the first implementation • m: the index after first permutation • j: the index after the second permutation • ---------------------------------------------------------------------------- • 1st permutation [for carriers] • m = (Ncbps/16)*mod(k,16)+floor(k/16); • 2nd permutation [for bits constellation mapping on carriers] • j=s*floor(m/s)+mod((m+Ncbps-floor(16*m/Ncbps)),s);

  9. 2-steps Interleaver (II)

  10. 16-QAM modulation • 16-QAM modulation • Gray mapped • Normalized constellation average power

  11. OFDM Transmitter: Data&Pilots, Zero Padding, Shaping, Cyclic Prefix (I) • 192 Data carriers • 8 Pilot carries • 0 DC carrier • 55 zero carriers added

  12. PRBS for pilot modulation Sample of a DL sequence: Corresponding sample of an UL sequence: OFDM Transmitter: Pilots (II) • Pilots BPSK modulated • Uses a PRBS generator of x11 + x9 + 1 • Initialized in DL with the vector: [1 1 1 1 1 1 1 1 1 1 1] • Why can’t we always transmit all 1s on the pilots without the need of the PRBS generator?

  13. OFDM Transmitter: Zero Padding (II) Freq axis: 0 → Fs • 55 zeros carriers are padded. • They will take the guard bands role. • Reshaping is done to ensure the spectrum falls off on both sides when plotted from –Fs/2 to Fs/2 Freq axis: -Fs/2 → Fs/2

  14. OFDM Transmitter: IFFT & Cyclic Prefix (III) After IFFTbefore CP • Tg/Tb ratio of ¼ used. Thus CP is 1/fourth the length of data time • Tg/Tb ratios specified by the protocol are: ¼, 1/8, 1/16, 1/32. Question: it does not specify when to use them. After CP Received Spectrum after the AWGN channel

  15. Receiver side

  16. OFDM receiver • Reciprocal work of the OFDM transmitter: • Remove Cyclic Prefix (assuming synchronization) • Perform the FFT • Remove the zero padding and reorder • Separate the data carriers from the pilot carriers

  17. Received signal • AWGN channel is used • If a Rayleigh channel is to be used, the receiver side would need a channel equalization section with the usage of the pilots in the channel estimation (currently pilots are ignored after being removed from the received OFDM frame).

  18. QAM demodulation & 2-stepsDe-interleaving

  19. Viterbi decoding • Using a trellis generated from the polynomial of constraint length 7, and the polynomials G1=171oct, and G2=133oct. • Traceback depth specified to be equal to 34. • It can be possible if the future to use soft decisions, LLRs, in decoding.

  20. Reed Solomon decoding • Some work is needed to compensate for the delay introduced by the Viterbi decoder. • Reed Solomon decoding is done, and tail byte removed. • Num of corrected is also outputted, with a -1 when the errors exceeding the max allowed bit errors; in this case equals to T =8.

  21. De-randomization • Same operation as in the Randomization • XORing with the same PRBS generator will retrieve back the data

  22. Bit Error Rate • Bit Error Rate is displayed, along with, • Number of bits in error, and • The total number of bits compared with the original stream of raw data.

  23. Generated BER curve for theIEEE 802.16d, 256-FFT, 16QAM, RS(64,48,8) & CC rate of 2/3

  24. BER curves over AWGN channel; incremental effects of channel coding

More Related