1 / 57

Measurement and the Metric System

Measurement and the Metric System. Standards of Measure. One cubit ?. Standards of Measure. Standards of Measure. When two people work together, they should both use the same standards of measure. Standards of Measure.

amity
Download Presentation

Measurement and the Metric System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Measurement and the Metric System

  2. Standards of Measure • One cubit ?

  3. Standards of Measure

  4. Standards of Measure • When two people work together, they should both use the same standards of measure.

  5. Standards of Measure • http://news.bbc.co.uk/1/shared/spl/hi/sci_nat/03/race_to_mars/timeline/html/1999.stm • September 1999Another Nasa space craft, Mars Climate Orbiter, is lost as it arrives at the Red Planet. A mix-up over units for a key space craft operation is blamed - one team used English units while the other used metric.

  6. SI Units

  7. Derived SI Units • http://physics.nist.gov/cuu/Units/SIdiagram.html

  8. Prefixes for SI Units • http://en.wikipedia.org/wiki/SI • http://en.wikipedia.org/wiki/SI_prefix

  9. Prefixes for SI Units • http://en.wikipedia.org/wiki/SI_prefix

  10. Metric System • During the 1790s, a decimal system based on our number system, the metric system, was being developed in France. • Easy to use • Easy to remember • Uses prefixes, that made the basic units larger or smaller by multiples or fractions of 10 • For example: 1km = 1000 m = 10,000 dm = 100,000 cm 1 mi = 1760 yd = 5280 ft = 63,360 in • The only country left behind is the USA.

  11. Imperial and U.S. customary systems of measurement • http://en.wikipedia.org/wiki/Comparison_of_the_Imperial_and_US_customary_systems • Both the Imperial (UK and Canada) and U.S. customarysystems of measurement derive from earlier English systems. • Comparison of Imperial and U.S. volume measures 1 liquid U.S. gallon = 3.785 411 784 litres ≈ 0.833 Imperial gallon 1 Imperial gallon = 4.546 09 litres ≈ 1.201 liquid U.S. gallons On January 1, 1983, the metric systems and SI units were introduced in Canada.

  12. Scientific Notation • Scientists often use very large or very small numbers that can not be conveniently written as fractions or decimal fractions. • For example, the thickness of an oil film on water is about 0.0000001 m • In scientific notation it is 1 x 10-7 m 0.1 = 1 x 10-1 0.001 = 1 x 10-3 10,000 = 1 x 104

  13. Systems of Measurement United States Customary System (USCS) • Formally called British System • Used in the US and Burma • Length: foot • Weight/force: pound • Time: second Systeme International (SI) • Also called the Metric or International System • Used everywhere else in the world!

  14. Systeme International (SI)

  15. SI Conversions • Major advantage – the decimal system – all digits are related to one another – multiples of 10! 1 kilometer = 1000 meters = 100,000 cm 1 meter = 100 cm = 0.001 kilometer

  16. Scientific Notation 0.1 = 1 x 10-1 0.001 = 1 x 10-3 10,000 = 1 x 104 • Any number can be written as a product of a number between 1 and 10 and a power of 10. • In general, M x 10n; Where M, is the a number between 1 and 10 and n, is the exponent or power of 10.

  17. Metric Length • The basic SI unit of length is the metre (m). • Originally 1m = distance from the equator to either pole/10,000,000 • “The metre is the length pf path traveled by light in a vacuum during a time interval of 1/299,792,458 s • Km • m • cm

  18. Conversion Factor • A conversion factor is an expression used to change from one unit to another. • Expressed as a fraction whose numerator and denominator are equal quantities in two different units. • The information necessary for forming a conversion factor is usually found in their conversion table as follows: 1 m = 100 cm • So, the conversion factors are: 1 m and 100 cm 100 cm 1 m

  19. Conversion using Conversion Factor • So, convert 5m to cm: 5 m x 100 cm = 500 cm 1 m Where the unit of the denominator should be the same as the original unit, so they cancels out. • So, convert 7 cm to m: 7 cm x 1 m = 0.07 m 100 cm

  20. Conversion using units value Or, it can be converted as follows: 5 m = 5 x 1 m = 5 x 100 cm = 500 cm Similarly, 7 cm = 7 x 1 cm = 7 x 1 m = 0.07 m 100 1 m = 100 cm • 100 cm = 1 m • Therefore, 1 cm = (1/100) m

  21. Metric-English Conversion To change from an English unit to a metric unit or from a metric unit to an English unit, we use a conversion factor, from the relation 1 in = 2.54 cm. • So, the conversion factors are: 1 in and 2.54 cm 2.54 cm 1 in

  22. Area • The area of a plane surface is the number of square units that it contains. • To measure the surface area of an object, you must first decide on a standard unit of area. • Standard units of area are based on the square of standard lengths, for example 1 square m.

  23. Area • Find the area of a rectangle 5 m long and 3 m wide. • By simply counting the number of squares, we find the area of the rectangle is 15 m2. • Or, by using the formula A = l x w = 5 m x 3 m = (5 x 3) (m x m) = 15 m2

  24. Volume • The volume of a figure is the number of cubic units that it contains. • Standard units of volume are based the cube of standard lengths, such as cubic meter, cubic cm, cubic in.

  25. Volume • Find the volume of a rectangular prism 6 cm long, 4 cm wide, and 5 cm high. • To find the volume of the rectangular solid, count the number of cubes in the bottom layer and then multiply by the number of layers. • Or, V = l w h = 6 x 4 x 5 cm x cm x cm = 120 cm3

  26. Mass • The mass of an object is the quantity of material making up the object. • One unit of mass in the metric system is the gram (g). • The gram is defined as the mass of 1 cm3 of water at its maximum density (at 4 C). • Since the gram is so small, kg is the basic unit of mass in SI (Système international d'unités) .

  27. Weight • The weight of an object is a measure of the gravitational force or pull acting on an object. • The weight unit in the metric system is the newton (N). • An apple weighs about one newton. • A newton is the amount of force required to accelerate a mass of one kilogram by one meter per second squared. 1 N = 1 kg·m/s² • The pound (lb), a unit of force, is one of the basic English system units. It is defined as the pull of the earth on a cylinder of a platinum-iridium alloy that is stored in a vault at the U.S. Bureau of Standards. • 1 N = 0.225 lb • 1 lb = 4.45 N

  28. kg with weight • When the weight of an object is given in kilograms, the property intended is almost always mass. • Occasionally the gravitational force on an object is given in "kilograms", but the unit used is not a true kilogram: it is the deprecated kilogram-force (kgf), also known as the kilopond (kp). • An object of mass 1 kg at the surface of the Earth will be subjected to a gravitational force of approximately 9.80665 newtons (the SI unit of force). • http://en.wikipedia.org/wiki/Kilogram • http://en.wikipedia.org/wiki/Newton

  29. Time • The basic unit of time is second (s) in both system. • It was defined as 1/86400 of a mean solar day. • Now the standard second is defined more precisely in terms of frequency of radiation emitted by cesium atoms when they pass between two particular states; that is , the time required for 9,192,631,770 periods of this radiation.

  30. Electrical Units • The ampere (A) is the basic unit and is measure of the amount of electric current. Derived units are: Columb (C) – is a measure of the amount of electrical charge Volt (V) – is a measure of electric potential Watt (W) - is a measure of power

  31. Accuracy vs. Precision • Accuracy: A measure of how close an experimental result is to the true value. • Precision: A measure of how exactly the result is determined. It is also a measure of how reproducible the result is. • Absolute precision: indicates the uncertainty in the same units as the observation • Relative precision: indicates the uncertainty in terms of a fraction of the value of the result

  32. Accuracy • Physicists are interested in how closely a measurement agrees with the true value. • This is an indication of the quality of the measuring instrument. • Accuracy is a means of describing how closely a measurement agrees with the actual size of a quantity being measured.

  33. Error • The difference between an observed value and the true value is called the error. • The size of the error is an indication of the accuracy. • Thus, the smaller the error, the greater the accuracy. • The percentage error determined by subtracting the true value from the measured value, dividing this by the true value, and multiplying by 100.

  34. Error

  35. Significant Digits • The accuracy of a measurement is indicated by the number of significant digits. • Significant digits are those digits in the numerical value of which we are reasonably sure. • More significant digits in a measurement the accurate it is:

  36. Significant Digits • More significant digits in a measurement the accurate it is: E.g., the true value of a bar is 2.50 m Measured value is 2.6 m with 3 significant digits. The percentage error is (2.6-2.50)*100/2.50 = 4% E.g., the true value of a bar is 2.50 m Measured value is 2.55 m with 3 significant digits. The percentage error is (2.55-2.50)*100/2.50 = 0.2% Which one is more accurate? The one which has more significant digits

  37. Rules for Determining “Significant Digits” • All non zero digits are significant • All zeros between significant non zero digits are significant. 450.09  5 significant digits • A zero in a number (> 1) which is specially tagged, such as by a bar above it, is significant. 250,000  3 significant digits • Zeros at the right in whole number. 5600  2 significant digits • All zeros to the right of a significant digits and a decimal point. 5120.010  7 significant digits • Zeros at the left in measurements less than 1 are not significant. 0.00672  5 significant digits

  38. Determine the “Accuracy” and “Precision” 3463 m 4 S.D.s 1m 3005 km 36000  8800 V 1349000 km 0.00632 kg 0.0060 g 14.20 A 30.00 cm 100.060 g 6 SDs 0.001 g 0.00004 m 2.4765 m

  39. Precision • Being precise means being sharply defined. • The precision of a measuring instrument depends on its degree of fineness and the size of the unit being used. • Using an instrument with a more finely divided scale allows us to take a more precise measurement.

  40. Precision • The precision of a measuring refers to the smallest unit with which a measurement is made, that is, the position of the last significant digit. • In most cases it is the number of decimal places. e.g., • The precision of the measurement 385,000 km is 1000 km. (the position of the last significant digit is in the thousands place.) • The precision of the measurement 0.025m is 0.001m. (the position of the last significant digit is in the thousandths place.)

  41. How precise do we need? • Physicists are interested in how closely a measurement agrees with the true value. • That is, to achieve a smaller error or more accuracy. • For bigger quantities, we do not need to be precise to be accurate.

  42. How precise do we need? • For bigger quantities, we do not need to be precise to be accurate. E.g., the true value of a bar is 25 m Measured value is 26 m with 2 significant digits. The percentage error is (26-25)*100/25 = 4% E.g., the true value of a bar is 2.5 m Measured value is 2.6 m with 2 significant digits. The percentage error is (2.6-2.5)*100/2.5 = 4% Which one is more precise? The one which has the precision of 0.1m Which one is more accurate? Both are same accurate as both have 2 significant digits

  43. Accuracy or Relative Precision • An accurate measurement is also known as a relatively precise measurement. • Accuracy or Relative Precisionrefers to the number of significant digits in a measurement. • A measurement with higher number of significant digits closely agrees with the true value.

  44. Estimate • Any measurement that falls between the smallest divisions on the measuring instrument is an estimate. • We should always try to read any instrument by estimating tenths of the smallest division.

  45. Accuracy or Relative Precision • In any measurement, the number of significant figures are critical. • The number of significant figures is the number of digits believed to be correct by the person doing the measuring. • It includes one estimated digit. • A rule of thumb: read a measurement to 1/10 or 0.1 of the smallest division. • This means that the error in reading (called the reading error) is 1/10 or 0.1 of the smallest division on the ruler or other instrument. • If you are less sure of yourself, you can read to 1/5 or 0.2 of the smallest division. • http://www.astro.washington.edu/labs/clearinghouse/labs/Scimeth/mr-sigfg.html

  46. Exact vs. Approximate numbers • An exact number is a number that has been determined as a result of counting or by some definition. • E.g., 41 students are enrolled in this class • 1in = 2.54 cm • Nearly all data of a technical nature involve approximate numbers. • That is numbers determined as a result of some measurement process, as with a ruler. • No measurement can be found exactly.

  47. Calculations with Measurements • The sum or difference of measurements can be no more precise than the least precise measurement. 54 mm Using a ruler, Precision of the ruler is 1 mm But actually it can be anywhere between 53.50 to 54.50 mm 42.28 mm Using a micrometer This means that the tenths and hundredths digits in the sum 96.28 mm are really meaningless, the sum should be 96 mm with a precision of 1 mm

  48. Calculations with Measurements • The sum or difference of measurements can be no more precise than the least precise measurement. • Round the results to the same precision as the least precise measurement. 54 mm Using a ruler, Precision of the ruler is 1 mm But actually it can be anywhere between 53.50 to 54.50 mm 42.28 mm Using a micrometer This means that the tenths and hundredths digits in the sum 96.28 mm are really meaningless, the sum should be 96 mm with a precision of 1 mm

  49. Calculations with Measurements • The product or quotient of measurements can be no more accurate than the least accurate measurement. • Round the results to the same number of significant digits as the measurement with the least number of significant digits. • http://www.astro.washington.edu/labs/clearinghouse/labs/Scimeth/mr-sigfg.html Length of a rectangle is 54.7 m Width of a rectangle is 21.5 m Area is 1176.05 m2 Area should be rounded to 1180 m2 To express with same accuracy

  50. Rounding Numbers • To round a number to a particular place value: • If the digit in the next place to the right is less than 5, drop that digit and all other following digits. Replace any whole number places dropped with zeros. • If the digit in the next place to the right is 5 or greater, add 1 to the digit in the place to which you are rounding. Drop all other following digits. Replace any whole number places dropped with zeros

More Related