1 / 15

2004 MAPLD International Conference Aerospace Mishaps and Lessons Learned STS-86 SAFER Keith E. Van Tassel Group Lead, P

2004 MAPLD International Conference Aerospace Mishaps and Lessons Learned STS-86 SAFER Keith E. Van Tassel Group Lead, Pyrotechnics NASA – Johnson Space Center September 2004. MAPLD 2004. S IMPLIFIED A ID F OR E VA R ESCUE. MAPLD 2004.

aren
Download Presentation

2004 MAPLD International Conference Aerospace Mishaps and Lessons Learned STS-86 SAFER Keith E. Van Tassel Group Lead, P

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 2004 MAPLD International Conference Aerospace Mishaps and Lessons Learned STS-86 SAFER Keith E. Van Tassel Group Lead, Pyrotechnics NASA – Johnson Space Center September 2004

  2. MAPLD 2004 SIMPLIFIED AID FOR EVA RESCUE

  3. MAPLD 2004 Astronaut Mark Lee is floating above the Shuttle's payload bay during the first test of the Simplified Aid for EVA Rescue (SAFER). SAFER is a device, attached to the bottom of the EMU backpack, that allows the astronauts to maneuver themselves around. It was developed as a self-rescue device to be used during the assembly and maintenance of the International Space Station in the event that a tethered astronaut breaks away during an EVA, and a Shuttle is not available to assist in the rescue.

  4. MAPLD 2004

  5. MAPLD 2004

  6. MAPLD 2004 Pyro Isolation Valve SAFER PYROVALVE 23

  7. MAPLD 2004

  8. MAPLD 2004

  9. MAPLD 2004 NSI PERFORMANCE CHARACTERISTICS • 1 AMP 1 WATT DEVICE • 3.5 AMP ALL FIRE • 1.0 AMP NO FIRE TYPICAL FIRING MODES • Capacitive Discharge: 20 to 40 V, 680 microfarads • Constant Current: 5 Amps

  10. MAPLD 2004 The SAFER Flight Unit was activated during STS-86 Demonstration Test Objective (DTO) with EVA astronaut secured in foot restraints Post flight SAFER checkout identified that NSI had not fired • Pressure from the NSI operates a normally closed pyrovalve. The pyrovalve opens hermetically sealed nitrogen tank needed for propulsion. Subsequent trouble shooting revealed that the firing circuit did not provide enough current to guarantee that the NSI would fire 100% of the time. • Temperature increase in bridgewire (BW) due to current flow caused BW resistance to increase significantly • Increased resistance in constant voltage source firing circuit caused firing current to drop • Resulting firing current was below the minimum all-fire level of the BW • Current was at approximately the 60% fire level

  11. MAPLD 2004 HOW DID THIS HAPPEN? COMMUNICATION • WHAT A PYRO ENGINEER MEANS WHEN HE SAYS CONSTANT CURRENT • DESIGN REVIEWS • FIRING CIRCUIT DESIGN TESTING • NSI “EMULATOR” • NUMBER OF ACTUAL TEST FIRINGS SCHEDULE PRESSURE COMMUNICATION

  12. MAPLD 2004 COMMUNICATION • WHAT A PYRO ENGINEER MEANS WHEN HE SAYS CONSTANT CURRENT • Three basic types of firing circuits • Capacitive Discharge – most common at NASA • Constant Current – occasionally used • Constant Voltage - rare • Typical BW resistance is 1.05 Ohms. • Current flows through the BW causes the BW resistance to increase to around 1.6 Ohms • Since BW resistance changes during firing, a constant current firing circuit must be able to adjust the voltage to compensate for the resistance increase • Minimum all-fire level is 3.5 amps constant current. • Recommended constant current is 5.0 amps • Design engineer designed circuit providing 4.2 constant volts. • Since the bridge wire resistance increases when current is sent through it, the actual current ended up being around only 2.8 amps. • At 2.8 amps, you have approximately 60% chance of the NSI firing.

  13. MAPLD 2004 COMMUNICATION • DESIGN REVIEWS • Design Reviews were brief • FIRING CIRCUIT DESIGN • Pyro Engineer did not have an opportunity to review firing circuit design TESTING • Pyro engineers were not consulted about acceptable number of qualification firing tests. • Only two SAFER qualification test firings were performed. • These test firings were performed on the qualification unit only. • No firings were performed on any of the flight units • Typical system level qualification testing using pyros has a minimum of 15 firings • Other SAFER “firings” were done using a 1-ohm resistor to simulate the NSI. • Pyro engineer was not consulted about the use of an NSI simulator.

  14. MAPLD 2004 RESULTANT ACTIONS REDISIGNED FIRING CIRCUIT Capacitive Discharge Detailed design review of new firing circuit with independent assessment DELTA CDR A formal, in-depth review with independent assessment DELTA QUALIFICATION TESTING AND ACCEPTANCE TEST FIRINGS 17 test firings – included firing all flight units as part of Acceptance Testing Monitor firing circuit current during tests EMI testing Bruceton test on firing circuit NSI USER’S GUIDE

More Related