1 / 38

NANOFLUIDS

NANOFLUIDS. OVERVIEW OF PRESENTATION. Introduction Conventional methods of heat transfer Materials for nanoparticles and fluids Preparation of nanofluids Modeling of thermal conductivity Possible microscopic mechanisms Thermal conductivity Convection Boiling Advantages of nanofluids

Download Presentation

NANOFLUIDS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. NANOFLUIDS

  2. OVERVIEW OF PRESENTATION • Introduction • Conventional methods of heat transfer • Materials for nanoparticles and fluids • Preparation of nanofluids • Modeling of thermal conductivity • Possible microscopic mechanisms • Thermal conductivity • Convection • Boiling • Advantages of nanofluids • Disadvantages of nanofluids • Application and Further research • Conclusions • References

  3. INTRODUCTION • Need for efficient working • Miniaturization • Proper working • Low conductivity of conventional fluids [water, ethylene glycol, mineral oil] • Limitation of solid-liquid suspensions

  4. INTRODUCTION(CONTI…) • Suspension of nanometer (10-9) sized particles • Nanofluid technology (i) Nanoscience (ii) Nanotechnology (iii) Thermal engineering • Coined by Choi • Less than 100nm • Low volume fraction Bright field image of Cu nanoparticles (<10nm)dispersed in ethylene glycol

  5. CONVENTIONAL METHODS OF HEAT TRANSFER Disperse micrometer or millimeter sized particles in heat transfer fluids. Major problem • Settling down • Cause wearing • Large mass J.A. Eastman,” Mechanisms of enhanced heat transfer in nanofluids”

  6. CONTI.. Increasing surface area /flow velocity Advantages • High surface to volume ratio • Thermal effectiveness Cannot be applied to miniaturized products, already been maximized

  7. NANOPARTICLES AND BASE FLUIDS Nanoparticles • Aluminum oxide (Al2O3) • Titanium dioxide (TiO2) • Copper oxide (CuO) Base fluids • Water • Oil • Ethylene glycol U.S. Choi and J.A. Eastman, “Enhanced heat transfer using nanofluids” U.S. Patent #6,221,275

  8. PREPARATION OF NANOFLUIDS Inert gas condensation (2-step). Schematic of IGC . 1-capacitance manometer 2-LN2 filling tube 3- LN2 exhaust 4-glass vacuum chamber 5-cold plate 6-evaporation boat 7-moisture trap 8-argon gas cylinder 9-disc shutter, 10-high vacuum valve, 11-vacuum pumps, 12-power supply Muhammad Raffi, “Synthesis and characterization of nanoparticles”

  9. CONTI… Advantages of IGC • Wide variety of nanopowders • Commercialized Disadvantages • Agglomeration • Poor dispersion • Direct evaporation • Chemical vapor deposition • Chemical precipitation } 1-step

  10. THERMAL CONDUCTIVITY MODELS 1) Maxwell’s model(Classical model) Applicable to • Homogenous • Isotropic composite material with randomly dispersed non interacting spherical particles having • uniform size • dilute solutions Appropriate for predicting properties such as electrical conductivity, dielectric constant and magnetic permeability

  11. CONTI.. The expressions for the ratio of effective conductivity to fluid conductivity • (ke / kf)=1+([3ϕ (α-1)]/[(α+2)-ϕ(α-1)]) • ϕ -volume fraction or concentration of the dispersed particles • α -ratio of thermal conductivity of the particle to that of the fluid and

  12. CONTI.. 2) Hamilton and crosser model (H&C model) • Applicable to non-spherical The expressions for the ratio of effective conductivity to fluid conductivity is • (ke / kf)=[α+(n-1)(1+ ϕ(α-1))]/ [α+(n-1)- ϕ(α-1)] • n -shape factor to account for differences in the shape of the particles

  13. CONTI… 3) Jang and Choi model Four modes of energy transport • Collision of the base fluid molecules • Thermal diffusion in particles inside the base fluids • Collision between particles • Thermal interactions of particles with the base fluid molecules

  14. POSSIBLE MICROSCOPIC MECHANISMS Keblinski et al.(2002)-four possible mechanisms: • Brownian motion • Molecular-level layering of liquid • Ballistic nature of heat conduction • Nanoparticle clustering

  15. COMPARISON OF DIFFERENT DIFFUSION TIME SCALES For water based Nanofluids containing 5nm particle size at 300K specifications are as follows: kf= 0.613 W/m-K cp=4.179 kJ/kg-K µ= 0.798 x 10-3 kg/m-s ρ= 995.7 kg/m3 M. Reza Azizian, Hikmet S. Aybar, Tuba Okutucu, “effect of nanoconvection on thermal conductivity of nanofluids”

  16. THERMAL CONDUCTIVITY Measurement method: Hot-wire transition • Time 2-8 sec • No convection • Heat applied suddenly Platinum wire(1.06*10-7Ωm) k={q/[4π(T2-T1)]}*ln (t2/t1) k-conductivity T-temperature T-time S.K.Das and others, ”nanofluids science and technology”

  17. THERMAL CONDUCTIVITY OF OXIDE NANOFLUIDS 1) Measurement method: THW 2) Linear relation between thermal conductivity and volume fraction 3) Enhancement in water-Cuo nearly equals ethylene glycol-Al2O3 system 4) Ethylene glycol-Cuo (24nm)system indicates maximum enhancement 5) Water- glycol-Al2O3 (38nm)system least increment Enhanced thermal conductivity of oxide nanofluids (Lee et al., 1999)

  18. CONTI… Comparison of ethylene glycol-Al2O3 system using H-C theory Comparison of ethylene glycol-CuO system using H-C theory Size of the dispersed particles also effects conductivity

  19. EFFECT OF pH AND SIZE ON CONDUCTIVITY 1) At isoelectric point(IEP): repulsive force between particles are zero-agglomeration 2) Hydration forces increase at pH value away from pHIEP–mobility Thermal conductivity enhancement with pH, Xie et al.(2002b)

  20. CONTI… Nonmonotonic behavior: 1) Conductivity increases with specific surface area (SSA) up to SSA=28 m2/g and then decreases 2) As SSA increases with i.e. at reduced diameter, surface area effect is dominating, hence conductivity increases 3) Beyond the maximum, size effect is dominant, phonon scattering effect causes decrease in conductivity Thermal conductivity enhancement with SSA for alumina particles, Xie et al.(2002b)

  21. PARTICLE AGGLOMERATION-TIME SCALE 1)Due to van der waals forces 2)Agglomeration is time dependent 3)Decrease in conductivity due to lower surface to volume ratio and concentration 4)Viscosity also increases with concentration Karthikeyan, Philip and Raj, ”Time dependence thermal conductivity of Cuo-water nanofluid”

  22. Karthikeyan, Philip and Raj ,0.1% volume fraction of CuO particles in water after a) 20 minutes b) 60 minutes c) 70 minutes

  23. CONDUCTIVITY OF METALLIC NANOFLUIDS • Three samples of CuO-ethylene glycol were taken • first two stabilizer not added • Labeled old- kept for 2 months • Labeled new- 2 days old • 1% Thioglycol acid added • 40%increase in conductivity of • acidic nanofluid for 3% • Concentration. • Thioglycol acid improves • dispersion • Metallic nanofluids greater • conductivity compared to oxide • nanofluids Effective conductivity of CuO-ethylene glycol nanofluid, Eastman et al. (2001)

  24. CONVECTION IN NANOFLUIDS Experimental investigations • Nanofluids at low volume fraction behave like Newtonian fluids. • Viscosity, temperature, heat capacity, flow velocity, pressure drop etc have a bearing effect on heat transfer coefficient ‘h’ .

  25. Animation of shadowgraph showing travelling waves moving across the top surface, in contrast to the fixed pattern seen in classic convection. This "oscillating" convection occurs if the nanoparticles are initially evenly dispersed throughout the fluid. If not, the convection is completely shut down http://www.google.co.in/url?q=http://focus.aps.org/story/v23/st9&sa=X&ei=n_VETcz7JseIrAf4_KQM&ved=0CCoQuAIwAg&usg=AFQjCNG_ETkh3VJSP9DVAVdNFpvlSHX32w

  26. CONTI… 1)Alumina and Titania particles with mean diameter 13nm and 27nm respectively 2)‘h’ increased 45% at 1.34% volume fraction and 75% at 2.78% for alumina particles in water 3)Greater heat transfer by Alumina-water fluid than using Titania particles 4)Pressure drop decreased significantly compared to increase in ‘h’ Pak and Cho, heat transfer coefficient vs Reynlods number

  27. CONTI… 1)Entry length effect 2)In laminar flow boundary layer is thin hence ‘h’ is higher 3)Enhancement increases with concentration only at entrance Measured local heat transfer coefficient for convection inside a tube, Wen and Ding (2004)

  28. BOILING OF NANOFLUIDS • Boiling is the process of changing liquid into vapor at a constant temperature known as saturation temperature at a given pressure • Critical heat flux is the flux at which a small change in flux will lead to a larger in wall superheat Boiling classified as: • Pool boiling –heat flux • Film boiling-mass flux

  29. CONTI… • CHF is the maximum heat flux under which a boiling surface stays in nucleation regime of boiling • Film boiling undesirable because portions of the surface become covered with vapor • Increase in CHF is due to increase in Surface roughening (more nucleation sites) • Nucleating small bubbles is desirable as it helps in agitation of fluid. • Boiling heat transfer depends on heat of vaporization, density of vapor and liquid, and surface tension and not on ‘k’

  30. CHF IN POOL BOILING Under lower volume fraction of vapor flow boiling is similar to nucleate boiling and depends mostly on heat flux flux Results show a 50% to 200% rise in CHF over pool boiling of water Upto 0.01 g/l CHF increases exponentially Beyond 0.02 g/l CHF remains constant, 300% more than water Enhancement of CHF with particle concentration, You et al(2003)

  31. ADVANTAGES OF NANOFLUIDS • Compared with suspended particles of millimeter-or-micrometer dimensions which were used in base fluids to enhance heat transfer of such fluids, nanofluids exhibit higher thermal conductivities. • Many types of particles such as metallic and non-metallic, can be added into fluids to form nanofluids. • Suspended particles of the order of millimeters or even micrometers may cause some severe problems such abrasive action of the particles causes the clogging of flow channels, erosion of pipelines etc which are not that severe in case of nanofluids. • Micro and millimeter sized particles tend to settle rapidly. But nanoparticles can remain suspended in base fluids for a longer time. • The much larger relative surface area of nanoparticles compared to those of conventional particles improves heat transfer capabilities

  32. DISADVANTAGES • Processing cost • Agglomeration at higher pH value and also at high temperatures because of the ability of the particle to overcome thermal energy barrier leading to an increase in van der waals forces and hence resulting in decrease of conductivity • Use of surfactants for stability which results in lowering of conductivity due to the formation of a thermal boundary layer around the particles

  33. APPLICATION AND FURTHER RESEARCH • Cooling application • Biomedical • Tribology • Defense • Production of nanofluids • Key energy transport mechanisms • Thermal conductivity models • Long term stability • Green nanofluids

  34. CONCLUSION • Nanofluids containing small amounts of nanoparticles have substantially higher thermal conductivity than those of base fluids. The thermal conductivity enhancement of nanofluids depends on the particle volume fraction, size, type of base fluid and nanoparticles, pH value of nanofluids. • No clarity on the dominant mechanism responsible for drastic increase in nanofluids. • Although nanoconvection time scale can be compared with that of heat diffusivities scale, it cannot be ascertained as the dominant mechanism because in nanofluids the concentration of particles is low

  35. CONTI… • Increase in fluid velocity increased ‘h’ but led to a rise to a larger Darcy’s friction factor • Increase in heat transfer with concentration at entrance • CHF increases exponentially upto 0.01g/l

  36. REFERENCES • Sarit k. Das, Stephan U.S. Choi, Wenhua Yu, T. Pradeep-2007, “NANOFLUIDS: SCIENCE AND TECHNOLOGY”, A john Wiley & sons, INC., Publication. • S Kakac, B. Kosoy, D. Li, A.Pramuanjaroenkij-2010, “Microfluidics Based Microsystems: Fundamentals and Applications”, Springer Publication. • Prof. M. Kostic, Nanofluids, ”Advanced Flow And Heat Transfer Fluids”. • Visinee Trisaksria, Somchai Wongwises, “Critical review of heat transfer characteristics of nanofluids”. • Emily Pfautsch, “ Forced convection of nanofluids over a flat plate”. • Muhammad Raffi, “Synthesis and characterization of metal nanoparticles”.

  37. THANK YOU

More Related