1 / 21

PV System Design and Installation

PV System Design and Installation. LO 5B - Solar Energy Fundamentals. PV module Current-Voltage Curve. I-V Curve. Reference 3. Module Performance Parameters. Imp – Maximum Power Current, the current at the point On the I-V curve where the PV module produces

belle
Download Presentation

PV System Design and Installation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. PV System Design and Installation LO 5B - Solar Energy Fundamentals

  2. PV module Current-Voltage Curve I-V Curve Reference 3

  3. Module Performance Parameters Imp – Maximum Power Current, the current at the point On the I-V curve where the PV module produces Maximum power. At “knee” on I-V curve. Vmp – Maximum Power Voltage, the voltage at the point On the I-V curve where the PV module produces the Maximum power. At the “knee on the I-V curve. Maximum Power Point Imp Vmp Reference 2

  4. Module Design Parameters Isc – Short Circuit Current, the maximum current where there is no voltage. Voc – Open Circuit Voltage, the voltage where there no current. Isc Voc

  5. A different view Reference 2

  6. Measurement Conditions for PV Cells and Modules STC – Standard Testing Condition Irradiance = 1,000 watts/m2 Module Temperature = 25 deg C (77 deg F) PTC - PVUSA (utility consortium) Irradiance = 1,000 watts/m2 Ambient Temperature = 20 deg C Wind Speed = 1 meter/sec NOCT – Nominal Operating Cell Temperature Irradiance – 800 watts/m2 Ambient Temperature = 20 deg C PV Array: Open Circuit Wind Speed = 1 meter/sec

  7. PV module Current-Voltage Curve I-V Curve Reference 3

  8. Solar Intensity Module output is reduced with decrease in solar intensity (irradiance) Reference 2

  9. Temperature Module output is reduced with increasing temperatures Reference 2

  10. Temperature Correction Formula

  11. I-V Curve PV modules in Series Voltage of Array = Module Voltage x Number in Series Reference 2

  12. I-V Curve - PV modules in Parallel Array Current = Module Current x Number in Parallel Reference 2

  13. Where is Maximum Power Point for this array on the I-V Curve? Reference 3

  14. In Class Work Assignment • Breakout into groups • Calculate for String and Array • Isc (Short Circuit Current) • Voc (Open Circuit Voltage) • Imp (Max Operating Current) • Vmp (Max Operating Voltage) • 2. Provide information on temperature correction factors for voltage and current for the PV modules being used in the array.

  15. PV modules with different current outputs connected in series PV modules with lower current output will absorb current from modules with higher current output. Will lead to loss of power and potential overheating/damage of lower current PV modules Reference Class Book by Dunlop

  16. PV modules with different current outputs connected in parallel PV modules with different output currents can be connected in parallel with no harmful effect if string voltages are the same. Reference Class Book by Dunlop

  17. Impact of shading on PV array performance

  18. Bypass Diodes Bypass diodes are placed in PV modules to prevent damage from shading. Limits reverse bias voltage to 0.7 volts Diodes allow current to pass around shaded or open circuit PV cell. However, negative impact on power production as string voltage is less.

  19. More on Bipass Diodes • Bipass diodes are typically installed across every 18 to 20 cells in a PV module • Bypass diodes must be able to • Handle maximum operating voltage for the number of modules/cells bypassed, • Must be rated in excess of the maximum circuit current.

  20. Breakdown Voltage • Shading will cause PV cell to act as a resistance in circuit. • The cell develops a “reverse bias”. • Cell continues to pass current but the voltage is negative in direction. • High currents can lead to damaging levels of power dissipation through heat generation. • Cell will dissipate power in the form of heat, possibly damaging PV module. • Reverse bias conditions can also occur if, • PV module is in open-circuit condition in a series, • PV modules of different output current are put in series. • . Reference Class Book by Dunlop

More Related