Ethernet WAN Services

1. Ethernet WAN Services Ethernet Demarcation Devices Circuit 'Turn-Up' Testing & In-Service Assurance for Layer-2 and Layer-3 Network infrastructures

2. Ethernet (L-2) Network - Typical Scenario click anywhere to continue... Network Operation Centre (NOC) Console Value-Added Services Ethernet Service Provider Core Network Management Access Management Access Infrastructure Carrier Ethernet Circuit Infrastructure Carrier Ethernet Circuit Customer LAN Site B Customer LAN Site A Service Provider's Ethernet Demarcation Devices Ethernet Service Providers typically offer End-to-End or Core-to-Edge services for their customers, which frequently involve infrastructure, or at the least simple 'tail circuits', from 3rd party Carriers. In order to manage configurations and monitor both customer site access and network performance right out to the edges of the network, Ethernet Demarcation Devices (EDDs) are deployed at customer connection points, managed from the Service Provider's Network Operations Centre (NOC).

3. 1. Log in to EDD at Site A Ethernet Service Commissioning Tests 4. Results at A can be viewed from NOC console or transmitted to the NOC for inclusion directly to 'birth certificate' documentation click anywhere to 'build' then continue... Network Operation Centre (NOC) Console Ethernet Service Provider Core Network Customer Site A Customer Site B Infrastructure Carrier Ethernet Circuit Infrastructure Carrier Ethernet Circuit 3. Ethernet (L-2) Test traffic generated at A is looped back at B (SA/DA swapping, via 'SAM' hardware) for analysis back at A 2. Set-Up RFC2544 or Y.1564 Test in relation to customer SLA for service(s) between sites A and B Service Providers need initially to demonstrate that they have provisioned circuits in accordance with their customers requirements, so use this process for comprehensive Service Level Agreement (SLA) verification testing.

4. Subsequent 'In-Service' Monitoring click anywhere to 'build' then continue... NOC Console Log-In to set up Agreed Service Parameters (SLA) Log-In to set up Agreed Service Parameters (SLA) Pro-active SNMP 'Trap' alarm sent to NOC if agreed SLA not met Ethernet Service Provider Core Network Pro-active SNMP 'Trap' alarm sent to NOC if agreed SLA not met Customer Site B Customer Site A Infrastructure Carrier Ethernet Circuit Infrastructure Carrier Ethernet Circuit Y.1731 protocol exchanges time-stamped test packets in order to monitor service parameters relative to pre-defined customer SLA Subsequently, Service Providers require to monitor that SLA performance metrics continue to be satisfied 'in-service'. Pro-active alarming of potential 'SLA breach' conditions enable quick and effective remedial action, to the benefit of both Service Provider and customer.

5. Testing with an IP Network infrastructure? click anywhere to continue... NOC Console Service Provider Core Network Management Access Management Access MPLS (Layer-3, IP) Infrastructure Customer Site A Customer Site B Edge/Access Network (Typically Layer-2) Edge/Access Network (Typically Layer-2) Service Provider's Ethernet Demarcation Devices If the Service Provider is provisioning a Layer-3 network, typically an IP-VPN, but the customer is deploying their own Routers, then the Service Provider often still requires management visibility at the customer hand-off point. To enable End-to-End performance testing and monitoring, then Layer-2 test functionality alone within the Demarcation Devices is insufficient. Ethernet MAC packets cannot traverse Layer-3 elements of the network and Layer-3 (IP) packets are required. RFC2544 and/or Y.1564 testing is agnostic to packet type, so IP-addressed frames can just as readily be used, provided that the EDDs support this, along with the necessary IP configuration tools and processes (e.g. ARP for IP Gateway address mapping). Metrodata will support this functionality in the FCM9003 and FCM9005 EDDs.

6. And for in-service performance monitoring? click anywhere to 'build' then continue... NOC Console Log-In to set up Agreed Service Parameters (SLA) Log-In to set up Agreed Service Parameters (SLA) Service Provider Core Network Pro-active SNMP 'Trap' alarm sent to NOC if agreed SLA not met Pro-active SNMP 'Trap' alarm sent to NOC if agreed SLA not met MPLS (Layer-3, IP) Infrastructure Customer Site A Customer Site B Edge/Access Network (Typically Layer-2) Edge/Access Network (Typically Layer-2) TWAMP-light controller TWAMP protocol exchanges time-stamped test packets in order to monitor service parameters relative to pre-defined customer SLA TWAMP-light responder For networks including Layer-3 (IP) elements, the 'Two-Way Active Measurement Protocol' (TWAMP) performs a similar role to that of Y.1731 for 'Layer-2 only' networks, i.e. to monitor Latency and Jitter performance characteristics, providing alarms in the event of breaches of the customer's SLA criteria.

7. Metrodata Ethernet Demarcation Devices FCM9002 • Low cost, flexible EDD including single-level VLAN push/pop and support for circuit set-up testing (RFC2544 and Y.1564) plus Y.1731 for in-service Assurance, for Layer-2 Ethernet services only FCM9004 • Advanced Layer-2 EDD, supporting multi-level VLAN push/pop, comprehensive multi-flow testing and in-service Assurance FCM9003 (from Q3, 2015) • Adds IP-addressing to the FCM9002, for RFC2544 and Y.1564 testing, plus TWAMP-light for in-service monitoring, for Layer-2 and/or Layer-3 networks FCM9005 (from Q3, 2015) • Adds IP functionality similarly to the FCM9004 Metrodata's FCM9003 & FCM9005 platforms include both Layer-2 and Layer-3 circuit testing and in-service monitoring regimes, offering deployment flexibility for each of Layer-2, Layer-3 & hybrid networks.

8. Ethernet WAN Services Thank you! www.metrodata.co.uk