1 / 23

LTCC Chip Antennas – How to maximize performance Johanson Technology Inc.

LTCC Chip Antennas – How to maximize performance Johanson Technology Inc. Johanson Technology Inc. 4001 Calle Tecate Camarillo, CA 93012. Outline. Chip Antenna Characteristics Antenna Selection Considerations Circuit Design Constraints Layout Tips. Goal  To Maximize Performance.

famy
Download Presentation

LTCC Chip Antennas – How to maximize performance Johanson Technology Inc.

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. LTCC Chip Antennas – How to maximize performanceJohanson Technology Inc. Johanson Technology Inc.4001 Calle TecateCamarillo, CA 93012

  2. Outline • Chip Antenna Characteristics • Antenna Selection Considerations • Circuit Design Constraints • Layout Tips Goal  To Maximize Performance

  3. Motivation • Chip Antenna an efficient means of “connectivity” to modern portable electronic devices. • Miniature portable devices requires small antennas. • Can be internalized – i.e. “Concealed” within device.

  4. Pros • Chip antennas are small, cheap and performs well. • Bulky external “whip” type antenna thing of the past. Cons • Must be accounted for during initial circuit design stage • Interference, proximity de-tuning & degradation concerns.

  5. LTCC Chip Antenna

  6. Chip Antenna Characteristics -1 • Features Ag radiating element encapsulated in ceramic. • A quarter-wave ( λ/4 ) monopole system. • Works with GND plane to form dipole system. • Certain “No_GND” space necessary. • Small form factor, thin profile & light weight

  7. Chip Antenna Characteristics - 2 • Omni-directional diversity. • Linear Polarization. • Mounting configuration flexibility. • Frequency range supported: 0.8 GHz thru 10 GHz. • WiFi, BT, WiMAX, UWB, GSM, CDMA, GPS etc. • Suitable for Pick & Place.

  8. Antenna Selection Considerations -1 • Size • Frequency Band • Bandwidth • Polarization • Peak Gain • Ave Gain • Radiation Diversity Pattern

  9. Antenna Selection Considerations -2 • Successful Antenna design means harmonious interaction of the “seven” parameters. • Additional considerations for diversity systems – e.g. MIMO • Overall performance is also system dependent .

  10. Circuit Design Constraints • Size of the Circuit board. • Layout of the other board components. • Complexity of circuit. • Proper GND/No-GND dimensions. • “Tuned” Matching Circuitry • Shielding • Suitable Enclosure (material)

  11. Layout Tips -1 GND-bottom layer    GND-top layer   No ground area (yellow area) • Good Placements  • Bad Placements  & 

  12. Layout Tips -2 Don’t put the metal plate or battery above or below the yellow region Keep away any other metals from clearance area. Ground

  13. Layout Tips -3 GND GND • Further examples of good antenna placement schemes

  14. Layout Tips -4 • Antenna placement schemes for Diversity systems

  15. A. Antenna Matching Setup 50 W Feed line GND Test Board NO GND p-type Matching Pads Probe Soldering to Connect Probe_GND and PCB_GND Calibration Plane of Network Analyzer(NA)

  16. B. Measuring Steps • 1. One port calibration for NA • Open-Short-Load • Mount probe onto PCB and connect to NA • 3. Measure S11 of test board without antenna • S11_open save trace to memory of NA • 4. Measure S11 of test board with antenna and 0 W R mounted • S11_antenna • 5. Set NA to data/memory mode (S11_antenna/S11_open) • S11_match • 6. Match the trace of S11_match to 50W • (center of Smith chart at the desired frequency)

  17. Antenna Matching Example 1. Probe+Feed Line

  18. Antenna Matching Example 2. Probe+Feed Line (normalized)

  19. 3. Antenna (not normalized) (normalized)

  20. 4. Ant+shunt 3.9nH (normalized)

  21. 4. Ant+shunt 3.9nH+series 1.5pF (normalized)

  22. Matched Antenna Example 2450AT43A100 8.2nH 0.8pF 4.7nH Semi-rigid connector

  23. Conclusion – How to design • 1st – Determine the antenna location on board • 2nd – Select the most appropriate antenna model • 3rd - Implement antenna in conformance with design rules

More Related