1 / 16

EGR 334 Thermodynamics Chapter 9: Sections 3-4

EGR 334 Thermodynamics Chapter 9: Sections 3-4. Lecture 32: Gas Power Systems: The Diesel Cycle. Quiz Today?. Today’s main concepts:. Understand common terminology of a Diesel engine Be able to explain the processes of the Diesel Cycle

jam
Download Presentation

EGR 334 Thermodynamics Chapter 9: Sections 3-4

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. EGR 334 ThermodynamicsChapter 9: Sections 3-4 Lecture 32: Gas Power Systems: The Diesel Cycle Quiz Today?

  2. Today’s main concepts: • Understand common terminology of a Diesel engine • Be able to explain the processes of the Diesel Cycle • Be able to perform a 1st Law analysis of the Diesel Cycle and determine its thermal efficiency. • Be able to discuss limitations of the Diesel cycle compared to real Diesel engines. Reading Assignment: Read Chapter 9, Sections 5-6 Homework Assignment: Problems from Chap 9: 17, 20, 24, 38

  3. Sec 9.1 : Introducing Engine Terminology Two types of internal combustion engine • Spark Ignition (lower power & lighter) • Compression Ignition (spontaneous combustion) • Terminology Stroke: The distance the piston moves in one direction Top Dead Center : The piston has minimum volume at the top of the stroke. Bottom Dead Center : The piston has maximum volume at the bottom of the stroke. Clearance Volume : Min vol • Displacement Volume : Max vol. – Min vol. • Compression Ratio: Max vol. / min vol.

  4. Sec 9.3 : Air-Standard Diesel Cycle The Diesel cycle can operate using either the 4 or 2 stroke engine. Has a lower efficiency than the Otto cycle for the same compression ratio. Compression Ignition • More difficult to start when cold • Can have higher compression ratio • 16 <rDiesel <25 vs r≈11 for Otto cycle to avoid pre-ignition • Produces less CO, because excess air, but produces soot. Diesel Engine Animation at http://www.animatedengines.com/diesel.html

  5. Sec 9.3 : Air-Standard Diesel Cycle Process 1 – 2 : Isentropic compression of air (compression stroke). Process 2 – 3 : Constant pressure heat transfer to the air from an external source while moves down (ignition and part of power stroke) Process 3 – 4 : Isentropic expansion (remainder of power stroke) Process 4 – 1 : Completes cycle by a constant volume process in which heat is rejected from the air while piston is at bottom dead center • For the Otto cycle, the Qin occurs at constant volume (compressed cylinder) • For the diesel cycle, the fuel is injected while the cylinder is expanding, so the Qin occurs at constant pressure

  6. Sec 9.3 : Air-Standard Diesel Cycle Diesel Cycle analysis: Process 2 – 3 : Constant pressure heat transfer to the air from an external source while moves down (ignition and part of power stroke) • Use W23 with energy balance to find Q23. Remaining processes analysis is the same as for Otto cycle.

  7. Sec 9.3 : Air-Standard Diesel Cycle Find State 1 Properties Given T1 and r  use table to find u1 & h1. Find state 2: for isentropic process. or Find state 3: Use ideal gas law with p3 = p2. • were rc is the cutoff ratio: Find state 4. For Cold-Air Standard analysis: (isentropic processes 1-2 and 3-4) For state 2. For state 4.

  8. only for use between isentropic processes. A couple words about how and when to use relative pressure and relative spec. volume.

  9. Example (9.26): An air-standard Diesel cycle has a compression ratio of 16 and a cut-off ratio of 2. At the beginning of the compression, p1= 14.2 psi, V1= 0.5 ft3, T1= 520°R. Calculate • The heat added, in Btu. • The max T. • The thermal efficiency. • The mean effective pressure, • Given info: Diesel Cycle • State 1: p1=14.2 psi, T1=520 R • V1 = 0.5 ft3 • State 2: s2 = s1 • State 3: p3 = p2 • State 4: s4 =s 3 and v4=v1 • Compression ratio: r = V1/V2 =16 • Cutoff ratio: rc = V3/V2 = 2

  10. Example (9.26): An air-standard Diesel cycle has a compression ratio of 16 and a cut-off ratio of 2. At the beginning of the compression, p1= 14.2 psi, V1= 0.5 ft3, T1= 520°R. Calculate • The heat added, in Btu. • The max T. • The thermal efficiency. • The mean effective pressure, Determine State Properties: For State 1: Using Table A-22E: for T1 Read u 1 = 88.62 Btu/lbm h1 = 124.27 Btu/lbm pr1 = 1.2147 and vr1 = 158.58 Also using Ideal Gas Equation:

  11. Example (9.26): • For State 2: • (process 1-2 is isentropic) • Using compression ratio, r • Next use vr2 and Table A-22E to find other state properties: • T2 = 1502.5°R u2= 266.84 Btu/lbm • pr2= 56.27h2 = 369.85 Btu/lbm • Then:

  12. Example (9.26): • For State 3: • Using ideal Gas • process 2-3 constant pressure • Then using Table A-22E, use T3 to find properties • u3 = 586.16 Btu/lbm h3 = 792.03 Btu/lbm • p3r = 948.36 v3r = 1.174

  13. Example (9.26): • For State 4: • (process 3-4 is isentropic • and V4 = V1) • therefore: • Then using Table A-22E, use vr4 to find properties • u4 = 272.38Btu/lbm h4 = 377.47 Btu/lbm • pr4 = 60.46 T4 = 1530.8 R • then

  14. Example (9.26): • The heat added, in BTU. • The max T. • The thermal efficiency. • The mean effective pressure, • Heat is added during process 2-3 • Applying the 1st Law • Maximum Temperature is at Sate 3: Tmax = 3005 oR

  15. Example (9.26): • The heat added, in BTU. • The max T. • The thermal efficiency. • The mean effective pressure, • Thermal Efficiency: • Mean Effective Pressure: • where:

  16. End of Slides for Lecture 34

More Related