1 / 7

CLIC Survey and alignment: status and plans

CLIC Survey and alignment: status and plans. OUTLINE Short review of the activity Objectives and milestones for 2013 Report of outstanding / unresolved issues. CTC, 15/01/2013 Edms n° 1261487. Short review of the activity. Main objective: towards absolute measurements for the sensors

kimama
Download Presentation

CLIC Survey and alignment: status and plans

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CLIC Survey and alignment: status and plans • OUTLINE • Short review of the activity • Objectives and milestones for 2013 • Report of outstanding / unresolved issues CTC, 15/01/2013 Edms n° 1261487 H. MAINAUD DURAND on behalf of the CLIC active pre-alignement team

  2. Short review of the activity • Main objective: towards absolute measurements for the sensors • A lot of improvements on the cWPS linearity bench, allowing: • A linearity along ± 4 mm within 1 μm • An interchangeability within 5 μm • Absolute measurements within 8 μm • Tests on the oWPS on their linearity bench and in 169 have shown: • A linearity within 1 μm • An interchangeability within 6-8 μm • Absolute measurements ~ 15 μm • Short range systems from NIKHEF: • 6 chainplates ready to be installed on TBTM • An absolute calibration bench is under design @ NIKHEF • Main objective: towards micrometric displacements for the actuators • Linear actuators: validation on TBTM within the requirements • Cam movers: validation ok for standard cam movers • In both cases: a short displacement is achieved in 2-3 iterations (target < 1 μm) • Small cam mover: problem of pinion of gearbox that broke during first series of tests

  3. Short review of the activity • Development of laser based alternatives: • Validation of the concept on short range (3 m) with low cost components under progress. First results are promising. • Complementary tests to validate further system parameters using motorized displacement tables. • Consolidation and inter-comparison: • Huge problem of humidity in the TT1 tunnel (> 90%!), with a lot of difficulties met to re-install stretched wires and NIKHEF laser system. Everything seems ok now. • Tests of inter-comparison foreseen beginning of January.

  4. Short review of the activity • Validation of the fiducialisation strategy on TBTM: • Combination of CMM & AT401 measurements: alignment of the components within 15-20 μm • Pre-alignment using 2 independent strategies was coherent within 10 μm. • Control of the alignment of the components: • Methods developed (AT401, micro-triangulation, Romer arm) allow measurements better than 10μm. A few components controlled and fiducialized: PETS, DB quad, AS. • Active alignment: • All mechanical tests performed successfully when no constraints are applied on the girders (no vacuum, no waveguides) • Active alignment checked with success: alignment in less than 3 iterations within 1μm

  5. Short review of the activity • Spokes: • A setup has been built with 1m zerodur spokes, with semi spheres as contact and RasNik sensors on extremities: • Repeatability of contact with semi sphere: ~ 0.1 μm • Temperature expansion of zerodur very small • Young’s modulus of Zerodur checked • A setup with 3m zerodur spokes under design to prepare their calibration procedure

  6. Objectives for 2013 Task 1 Tasks 2, 3 & 4 • Laser based alternatives: • Development of a compact lambda sensor • Validation of Raschain sensors on short and long range through inter-comparison tests with WPS. • Precision and accuracy of a metrological network over 140 m (re-calculation using cWPS with improved absolute measurements) • Fiducialisation, control of alignment of TBTM during T° and transport tests • Validation of micrometric repositioning with additional constraints (vacuum and waveguides) • Design and manufacture of a calibration setup for spokes

  7. Outstdanding / unresolved issues • Development of a compact cam mover to be validated on 5DOF • Long term space in ISR • Collaboration with JINR • TZ32 • Safety in TT1 • All staff members (=experts) will work 100% of their time for LHC during LS1 • PACMAN

More Related