1 / 13

Process Mechanisms of Single Screw Extrusion

Process Mechanisms of Single Screw Extrusion. Dr Xueqin (Amy) Liu. Research Assistant Intelligent System & Control School of Electronics, Electrical Engineering & Computer Science. Presentation Outline. Standard set-up of SSE Process mechanisms Pressure development Inferential Viscosity

kipp
Download Presentation

Process Mechanisms of Single Screw Extrusion

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Process Mechanisms of Single Screw Extrusion Dr Xueqin (Amy) Liu Research Assistant Intelligent System & Control School of Electronics, Electrical Engineering & Computer Science

  2. Presentation Outline • Standard set-up of SSE • Process mechanisms • Pressure development • Inferential Viscosity • Laboratory SSE

  3. Standard Set-up of Single Screw Extruder

  4. Process Analysis • Identification/selection of manipulated variables, disturbance variables, and controlled variables is required for the proper design of control systems. partially reproduced from Iqbal, 2010

  5. Process Mechanisms Clamp-ring Adapter Reproduced from Tadmor and Klein, 1970

  6. Pressure Development

  7. Pressure Drop Through the Die

  8. Inferential Viscosity • In-line rheometer • Viscosity calculated from pressure drop and throughput rate (here linear with speed)

  9. Inferential Viscosity • Can be achieved using suitable rheological model and appropriate rheological parameters • Provides initial estimate of material viscosity

  10. Laboratory Single Screw Extruder Killion KTS-100, 25mm SSE (1995) with in-line rheometer

  11. References • Cogswell, F. N., Polymer melt rheology: A guide for industrial practice. Abington: Woodhead Publishing Ltd, 1981. • Han, C. D., What is the role of "pressure" in the use of capillary and slit flows to determine the shear-rate dependent viscosity of a viscoelastic fluid. Polymer engineering and science, 2008, 48(6): 1126 - 1140. • Liang, J.. Estimation of entry pressure drop during conical die flow of carbon black-filled rubber compound. Journal of Reinforced Plastics and Composites, 2004, 23(3): 1355-1363. • Cogswell, F. N., Measuring the extensional rheology of polymer melts. Transactions of the Society of Rheology, 1972, 16(3): 383 - 403. • C. Rauwendaal, Polymer Extrusion (4th edition). Carl Hanser Verlag, Munich, 2001.

  12. References • Cogswell, F. N., et al., Converging Flow of Polymer Melts in Extrusion Dies. Polymer Engineering and Science, 1972,12: 64 - 73. • McAfee, M. (2005). A soft sensor for viscosity control of polymer extrusion. Phd thesis, Queen’s University Belfast. • M. H. Iqbal, U. Sundararaj, and S. L. Shah, “New approach to develop dynamic gray box model for a plasticating twin-screw extruder,” Industrial & Engineering Chemistry Research, vol. 49, no. 2, pp. 648–657,2010. • X. Liu, K. Li, M. McAfee, and J. Deng, “‘soft-sensor’ for real-time monitoring of melt viscosity in polymer extrusion process,” in Decision and Control (CDC), 2010 49th IEEE Conference on, 2010, pp. 3469 –3474. • B. H. Maddock, “Measurement and analysis of extruder stability,” SPE Journal, vol. 20, pp. 1277–1283, 1964.

  13. Thank you for your attention

More Related