1 / 27

Materials Handling

Materials Handling. IENG 331 – Safety Engineering Carter J. Kerk , PhD, PE, CSP, PE Industrial Engineering Department South Dakota School of Mines & Technology. Reading Assignment. Brauer, Chapter 15 (Not Section 15-2) Required Review Questions, p. 278-9 7, 9, 11, 13

kylee
Download Presentation

Materials Handling

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Materials Handling IENG 331 – Safety Engineering Carter J. Kerk, PhD, PE, CSP, PE Industrial Engineering Department South Dakota School of Mines & Technology

  2. Reading Assignment • Brauer, Chapter 15 (Not Section 15-2) • Required Review Questions, p. 278-9 • 7, 9, 11, 13 • Recommended Review Questions • For those who have not or will not take IENG 321 • 1-5 • Read Section 15-2 • Not required

  3. 29 CFR 1910 Subpart N • 176 – Handling materials – general • 177 – Servicing multi-piece and single piece rim wheels • 178 – Powered industrial trucks • 179 – Overhead and gantry cranes • 180 – Crawler locomotive and truck cranes • 181 – Derricks • 183 – Helicopters • 184 - Slings

  4. Introduction • Non-manual materials handling • industrial trucks, tractors, cranes, conveyors • MH responsible for 20-25% of occupational injuries • MH responsible for 6% of OSHA general industry citations • Industry moves 50 – 180 tons of material for each ton produced • Manual materials handling (e.g., lifting) • IENG 321

  5. Types of Injuries & Accidents • Mass - Motion Hazards • Human Body • Pinch, fracture, sever, crush • Facilities, Equipment, Materials • gas lines, electrical lines, load-bearing walls, fires

  6. Materials Storage • Stacking • items should be stacked, blocked, interlocked, and limited in height • standards are not specific as to “how”, but are expected to achieve a desired “result”, therefore this is a “performance standard” • Side Issue • “Performance Standard” vs. “Specification Standard”?? • Housekeeping • sloppy storage housekeeping can lead to trip hazards, fire, pests, vegetation (outside)

  7. Material Storage (continued) • Egress • keep aisles and exits clear • During high production swings • be prepared for problems • Over-stacking • egress blocking • “creative” storage

  8. Industrial Trucks • Electric and internal combustion • Forklifts, tractors, platform lift trucks, motorized hand trucks, farm tractors, specialized industrial trucks

  9. Industrial Truck Selection • Complex because there are 11 different design classifications segregated by • type of power: diesel, electric, gasoline, LP gas • degree of hazard for which approved • Biggest hazard: fires & explosions • more expensive trucks have features to prevent ignition of fires and explosions • See next three diagrams for selection process

  10. Industrial Truck Operations • Fueling • no smoking around re-fueling stations • battery charging in designated areas only • better control of acid spillage, lifting of batteries, battery gases and fumes (ignitable) • good ventilation, emergency eyewash and shower • Internal Combustion Engines • CO hazard (50 ppm for 8 hour TWA) • Switch to electric? Better ventilation? Unnecessary idling?

  11. Truck Operations (continued) • Lighting requirements (illumination analysis) • Visibility • Hitchhikers & “elevators” • Unattended trucks (out of sight or > 25’) • Daily inspections (horns, lights, brakes) • Training Programs (29 CFR 1910.178)

  12. Forklift – Tipover and Stability

  13. Forklift – Transitions and Chocking

  14. Cranes • Many types (see next slide) • Rated loads (included safety factor) must be plainly marked • “Two-blocking” and “over-travel” • Prevent with: limit switches and bumpers • Electric shocks & power failures • Pendants - human factors issues (see slide) • Braking & “plugging” • Maintenance (lockout/tagout)

  15. Types of overhead cranes.

  16. Hand-held pendant for overhead crane. Human factors issues: directional incompatibility between crane movement and controls.

  17. Block & Tackle • Free body diagram

  18. Securing Wire Rope Loops “Don’t saddle a dead horse.” Right and wrong ways to secure wire rope loops using U-bolt clips. (a) Incorrect – “saddle” is on dead end of rope; (b) Incorrect – clips are staggered both ways; (c) Correct – all clips are placed with the saddle assembly on the live portion of the rope and the U-bolt on the dead end.

  19. Hoist Chains vs. Chain Slings Hoist chains are commonly misinterpreted to include chain slings. A separate standard exists for slings.

  20. Crane Hook Inspection

  21. Slings • Rope, fiber, chain, etc. • Rated capacity needed in conjunction with leg angles • 3 legs are better than 2, but 4 are not better than three, why? • Inspections

  22. Sling Angle

  23. Material Handling Industry of America • Trade Association • www.mhia.org • Case studies, equipment photos, applications

More Related