1 / 29

Current Mode Electronics for the Qweak Experiment Des Ramsay University of Manitoba/TRIUMF

Current Mode Electronics for the Qweak Experiment Des Ramsay University of Manitoba/TRIUMF Qweak Collaboration Meeting TRIUMF, Vancouver October 14-15 2005. Layout of the Qweak Experiment. Synthetic Quartz Scintillator Bars. Shielding Wall. Toroidal Magnet. Liquid Hydrogen Target.

mauli
Download Presentation

Current Mode Electronics for the Qweak Experiment Des Ramsay University of Manitoba/TRIUMF

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Current Mode Electronics for the Qweak Experiment Des Ramsay University of Manitoba/TRIUMF Qweak Collaboration Meeting TRIUMF, Vancouver October 14-15 2005

  2. Layout of the Qweak Experiment Synthetic Quartz Scintillator Bars Shielding Wall Toroidal Magnet Liquid Hydrogen Target Front-end electronics in extra shieldingbehind the wall Electron Beam

  3. shot noise: Nature of the Current Mode Signals 50 p.e. per event 50,000 e per event 1 M I-V 800 MHz VME digital signal integrator to DAQ 6.4 A 6.4 V x1000 in shielding outside hall

  4. I-V Preamplifier specs • Gain: Vout/Iin = 1 M with option of up to 10 M. Set by switches on board. • Output: 0 to +10V. Adjustable 2V offset. Drives 130 m RG-213 • Input: 10 A range. (e.g. +1 A to -9 A with +1 V offset.) Tolerates 5m of RG-62 on input. (Noise set primarily by length of input cable.) • Bandwidth: f3db = 30 kHz. (settles to <10-4 in 50 s) • Density: two amplifiers per module (one per detector bar). • Uses 5 V DC Supply. Ground fully isolated by internal DC-DC converter. • BNC connectors. Center conductor negative on input. • Small size for ease of shielding.

  5. MK1 Preamplifier at TRIUMF

  6. MK2 Preamplifier M Chan 1 gain Offset adjust 10 5 2 1 Chan 1 IN Out Chan 2 0.5 1 2.5 5 +5 V DC Chan 2 gain M • Reduced power supply noise • Switchable gains

  7. MK1 -- 1 M gain MK2 -- 225 pf Noise in Vrms Cin (pf) Measured Pspice open 50 24.4 93 70 51.2 179 100 83.0 275 120 112 726 190 182 Gain (M) Noise (Vrms) Channel 1 1 110 2 205 5 470 10 825 Channel 2 5 475 Noise Measurements on Preamps • Noise measured using x200, 50 kHz 5-pole amp, scope 500 kSPS • Noise referred to preamp output. • Used various lengths of RG-58C/U on input – measured capacitance. • Compare to shot noise (for 1 M) : • 70,000 V beam on • 10,000 V LED test • 300 V best-case battery test

  8. Qweak “1 kHz” Integration Scheme next spin state one spin state – (1/250) second 50 s settling time (not to scale) t 1 ms • four 1 ms integrals • target bubbling not seen on few ms time scale • Tsettle should be short to minimize dead time

  9. Existing Gzero Ion Source Signals • signals derived from 20 MHz crystal clock. • Qweak integrator should use this clock as well • Integration triggered by MPS (is present form OK?)

  10. TRIUMF Current Mode VME Integrator • Integration time software selectable 1/300 s to 1/30 s To be set as a fixed number of samples. • Integration triggered by external NIM signal (e.g. MPS) Triggers a selected time after leading edge and runs for pre-set number of samples. • Clocked by 20 MHz NIM signal from ion source. Divided by pre-scale to get sample rate. • Full differential high-impedance input provides common mode noise rejection. • 50 kHz, 5-pole anti-aliasing filter. • 18 bit ADC, 500 ksps. • Four 32-bit sums per integral available to DAQ on VME. No dead time between the four periods. • Buffered output permits reading previous integral during integration. • Eight integrators per single width VME.

  11. VME section details • VME registers • Sample period multiplier, k. Sample period = k*(1/sys_clock) • Number of samples per block, I • Number of sample blocks, m.  m = 1, 2, 4.  • Gate to Trigger Delay, n. Delay = n*(1/sys_clock). • Gate source, EXT/INT. • System Clock source, EXT/INT. • Block integration time = k*l*(1/sys_clock).Total integration time = k*l*m*(1/sys_clock).(In the FPGA it may be simpler to do 4 sample blocks and a total at all times.) • Data Readout • Sequence number. Shows if a measurement has been lost or skipped. • Block 1-4 sums. 32 bit. • Total sum. 32 bit. • Total number of samples actually taken -- Should equal k*l*m. • Valid data flag or new data ready flag. • Data buffer empty flag, if the data is buffered.

  12. Outstanding Questions • PREAMPS: • What radiation dose will they take? (Dave Mack is testing one) • What gain range should we use on the production amps? (MK2 has 1,2,5,10 and 0.5, 1, 2.5, 5 for evaluation.) • Where, exactly, should we mount them? • INTEGRATORS: • Are we using 1/250 s spin states, and is 50 s settling time reasonable? • Is ion source clock 20 MHz and can we get it as a NIM signal.? • Is MPS good as a trigger and can we get it as a NIM signal?

  13. I … 3 1 2 n t t T = nt Integral From Samples (rectangular rule) • approximate signal with samples • Q = (average I)(T) • band limit signal to small fraction of sampling frequency to eliminate the wiggles and kinks. • we impose an analog cutoff at 1/10 the sampling frequency

  14. Averaging of Digitization Noise • The 18 bit ADCs have ~0.5 LSB rms noise per sample. • This is reduced by averaging ~500 samples per integration. • This will only work if raw signal spreads over enough channels. • Assuming equivalent noise bandwidth 47 kHz (f3db= 30 kHz) and 18 bit ADC at mid range: • condition Q rms noise before channels channels • (e) integration () (FWHM) • beam ON 50,000 69 mV 1420 3339 • LED test 1,000 9.8 mV 201 472 • battery test 1 0.31 mV 6.3 15 • So this is OK even for very quiet signals.

  15. Comparison of Different Noise Sources rms noise on a 1 ms integral Conditionnoise (ppm) beam-ON shot noise 1120 shot noise during LED tests 160 shot noise during battery tests 5 preamplifier noise 2 digital integrator noise 1-2

  16. Changing gains and offset on the TRIUMF MK2 preamp Input side chan 2 chan 1 megohms 5 2.5 1 0.5 1 2 5 10 Output side • Channel 1 is shown set for 1 M and channel 2 for 0.5 M • To change gain move the set switch back towards the input side and move the one you want towards the output side. Note the gains increase away from the center. • The offset is set for 1.0 volts when shipped, but can be changed with the offset pot • To open the preamp for adjustment, remove the hex nuts from the OUTPUT side and remove the black screws from the INPUT side.

  17. Qweak Collaboration Spokespersons Bowman, J. David - Los Alamos National Laboratory Carlini, Roger (Principal Investigator) - Thomas Jefferson National Accelerator Facility Finn, J. Michael - College of William and Mary Kowalski, Stanley - Massachusetts Institute of Technology Page, Shelley - University of Manitoba Qweak Collaboration Members Armstrong, David - College of William and Mary Averett, Todd - College of William and Mary Birchall, James - University of Manitoba Botto, Tancredi - Massachusetts Institute of Technology Bruell, Antje - Thomas Jefferson National Accelerator Facility Chattopadhyay, Swapan - Thomas Jefferson National Accelerator Facility Davis, Charles - TRIUMF Doornbos, J. - TRIUMF Dow, Karen - Massachusetts Institute of Technology Dunne, James - Mississippi State University Ent, Rolf - Thomas Jefferson National Accelerator Facility Erler, Jens - University of Mexico Falk, Willie - University of Manitoba Farkhondeh, Manouchehr - Massachusetts Institute of Technology Forest, Tony - Louisiana Tech University Franklin, Wilbur - Massachusetts Institute of Technology Gaskell, David - Thomas Jefferson National Accelerator Facility Grimm, Klaus - College of William and Mary Hagner, Caren - Virginia Polytechnic Inst. & State Univ. Hersman, F. W. - University of New Hampshire Holtrop, Maurik - University of New Hampshire Johnston, Kathleen - Louisiana Tech University Jones, Richard - University of Connecticut Joo, Kyungseon - University of Connecticut Keppel, Cynthia - Hampton University Khol, Michael - Massachusetts Institute of Technology Korkmaz, Elie - University of Northern British Columbia Lee, Lawrence - TRIUMF Liang, Yongguang - Ohio University Lung, Allison - Thomas Jefferson National Accelerator Facility Mack, David - Thomas Jefferson National Accelerator Facility Majewski, Stanislaw - Thomas Jefferson National Accelerator Mammei, Juliette - Virginia Polytechnic Inst. & State Univ. Mammei, Russell - Virginia Polytechnic Inst. & State Univ. Mitchell, Gregory - Los Alamos National Laboratory Mkrtchyan, Hamlet - Yerevan Physics Institute Morgan, Norman - Virginia Polytechnic Inst. & State Univ. Opper, Allena - Ohio University Penttila, Seppo - Los Alamos National Laboratory Pitt, Mark - Virginia Polytechnic Inst. & State Univ. Poelker, B. (Matt) - Thomas Jefferson National Accelerator Facility Porcelli, Tracy - University of Northern British Columbia Ramsay, William - University of Manitoba Ramsey-Musolf, Michael - California Institute of Technology Roche, Julie - Thomas Jefferson National Accelerator Facility Simicevic, Neven - Louisiana Tech University Smith, Gregory - Thomas Jefferson National Accelerator Facility Smith, Timothy - Dartmouth College Suleiman, Riad - Massachusetts Institute of Technology Taylor, Simon - Massachusetts Institute of Technology Tsentalovich, Evgeni - Massachusetts Institute of Technology van Oers, W.T.H. - University of Manitoba Wells, Steven - Louisiana Tech University Wilburn, W.S. - Los Alamos National Laboratory Wood, Stephen Thomas - Jefferson National Accelerator Facility Zhu, Hongguo - University of New Hampshire Zorn, Carl - Thomas Jefferson National Accelerator Facility Zwart, Townsend - Massachusetts Institute of Technology

  18. Shot Noise equivalent noise bandwidth [Hz] or [A2] one-sided shot noise, charge quantum [C] current [A] • Example, 1 ms integration with beam on, assuming 800 MHz: • Q = 50,000 e • I = 6.4 A (800 MHz x 50,000 e) • B = 500 Hz • in = 7.2 nA rms (7.2 mV with a 1 M preamp) Note that in 1 ms, N = 8 x 105 counts. = 1120 ppm, same as 7.2 nA/6.4 A

  19. Qweak Front End Electronics

  20. Old “120 Hz” Qweak Integration Scheme next spin state one spin state – (1/30) second 200 s settling time (not to scale) t (1/120) • four 1/120 second integrals • multiples of 60 Hz cancel in sum • individual integrals show if 60 Hz (or odd harmonics) was present

  21. Block Diagram of Current Mode Electronics

  22. Prototype Dual Preamplifier

  23. current helicity - + - + - + - 6 A 3.6 pA (0.6 ppm p-p) ( ppm) time Size of Qweak Signal • figure shows regular spin flip; in practice use + - - + or - + + - • for 50 kHz noise bandwidth, rms shot noise is 70 nA • on a scope the noise band would be  100,000 x the signal !

  24. + helicity - helicity counts charge Q0 ADC error +s charge -s Differential Nonlinearity (DNL) Example • ADC reads S channels low below Q0 and jumps to S channels high above Q0 • This causes the measured asymmetry to depart from the real asymmetry, A0, by an amount , where  is in channels. • The DNL won’t introduce an asymmetry when none is there, it only changes an existing one.

  25. Summary of Electronics Needs

  26. TRIUMF E761 VME Module DSP serial port (diagnostic) eprom external trigger channel 1 channel 2

  27. Offset Number of samples Sample rate Calibration

  28. TRIUMF Parity 2 module -16-bit ADC - DSP summing - calibration mode - channel offset and gain - takes N samples when triggered - adjustable delay from trigger - delivers gate during integration - features can be programmed

More Related