1 / 22

Expanded Modes, Bus, External Memory

Expanded Modes, Bus, External Memory. Today: First Hour : Expanded Modes, Bus, Timing Section 4.1-4.7.2 of Huang’s Textbook In-class Activity #1 Second Hour : Interfacing external memory to 6811 Section 4.7.3 of Huang’s Textbook In-class Activity #2. 6811Operation Modes.

powa
Download Presentation

Expanded Modes, Bus, External Memory

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Expanded Modes, Bus, External Memory • Today: • First Hour: Expanded Modes, Bus, Timing • Section 4.1-4.7.2 of Huang’s Textbook • In-class Activity #1 • Second Hour: Interfacing external memory to 6811 • Section 4.7.3 of Huang’s Textbook • In-class Activity #2

  2. 6811Operation Modes • Single chip mode: a mode in which the 68HC11 functions without external address and data buses. • The 68HC11 has 5 I/O ports (A, B, C, D, and E) to use in this mode. • Expanded mode: a mode in which the 68HC11 has the capability to access a 64KB address space. • Port B is used as the upper address signals (A15-A8) • Port C is used as time-multiplexed address/data bus (A7/D7-A0/D0). • Only three I/O ports are available for direct use. • Choosing modes: • MODB, MODA pins (look up PRG!) • (1,0) => single chip; (1,1) => Expanded

  3. Expanded Mode PA7 PAI ROM-8KB PULSE ACCUMULATOR OC2 O PA6 C OC3 PA5 1 PORT PA4 OC4 RAM-256 bytes OC5 A PA3 IC1 PA2 PERIODIC INTERRUPT PA1 IC2 EEPROM-512 bytes COP WATCHDOG IC3 PA0 PE7 PD5 SS SCK PD4 PE6 SPI PE5 MOSI PD3 PORT PE4 PD2 MISO PORT DATA DIRECTION A/D E PE3 D CONVERTER PE2 PD1 TxD SCI PE1 RxD PD0 PE0 V REFH M68HC11 CPU V REFL ADDRESS DATA BUS RESET INTERRUPTS XIRQ IRQ HANDSHAKE I/O (V ) PPBULK DATA DIRECTION C XTAL PARALLEL I/O OSCILLATOR PORT B PORT C EXTAL E P P P P P P P P P P P P P P P P S S SINGLE MODA B B B B B B B B C C C C C C C C T T MODE CHIP LIR 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 R R SELECT MODB B A (V ) STBY A A A A A A A A A A A A A A A A AS 1 1 1 1 1 9 8 D D D D D D D D R/W 1 V EXPAND DD 5 3 2 1 0 7 6 5 4 3 2 1 0 4 POWER V SS

  4. Expanded Mode 1 MODB 1 MODA E R/W AS 68HC11 A15-A8 PB7-PB0 Bus AD7-AD0 PC7-PC0 Other pins not shown

  5. t t rise fall 1 90% V DD 0 10% V DD Timing Conventions Recap A real signal has nonzero rise and fall times 1 0 Single-signal waveform 1 0 Multiple-signal waveform

  6. Timing Conventions Recap Unknown signals (when they are changing) representation unknown (a) Single signal unknown (b) multiple signals Unknown signals

  7. Timing Conventions Recap A floating signal is represented by a level half way between logic high and low. Signal floating (a) Single signal Signals floating (b) multiple signals Floating signals

  8. Crystal & E-clock Crystal clock: 8 MHz => One cycle = 125 ns XTAL 125 ns E clock: 2 MHz => One cycle = 500 ns E 500 ns

  9. Bus Timing Diagram XTAL E R/W A15-A8 HI ADDR A7/D7-A0/D0 LO-ADDR DATA AS • Observe that AD lines active as address only for 1/2 E cycle • Most external memory devices need address lines active for 1E cycle • AS line to the rescue, combined with external address latch!

  10. 74373 Octal Transparent Latch with 3-State Outputs Positive edge triggered 11 CLK 11 LE 373 Stores an 8 bit number 18 19 H QH 17 16 G QG 14 15 F QF 13 12 /OE is active LO output enable Determines when register contents are visible at the outputs E QE 8 9 D QD 7 6 C QC 4 5 B QB 3 2 A QA OE 1 LE: Latch Enable. High => latch is transparent to data inputs

  11. Latching the Address 1 MODB 1 MODA E R/W AS 68HC11 Address A0-A7 latched on the falling edge of AS A15-A8 PB7-PB0 Bus AD7-AD0 PC7-PC0 Other pins not shown D0-D7 LE 0 OE 373 Q0-Q7 A0-A7

  12. Latching allows A7-A0 to be available for the second half of the E-clock cycle at the output of the latch Latching (contd) A0-A7 latched at falling AS edge 250 ns E AS 125 ns A7/D7-A0/D0 LO-ADDR DATA

  13. Do Activity #1 Now

  14. Memory Mapping • Memory mapping external memory => can access external memory using normal instructions and memory addresses. • Similar to I/O memory mapping • Address space assignment • - Use only unallocated memory space • - Allocated in units of 2n KB (n is an integer) • Allocated space for the 68HC11A8 • $0000-$00FF: SRAM • $1000-$103F: I/O registers • $B600-B7FF: EEPROM • $E000-$FFFF: ROM

  15. Consider an external 13-bit memory chip => 8KB Divide 64 KB space into eight 8KB blocks. Block number Address range $0000-$1FFF $2000-$3FFF $4000-$5FFF $6000-$7FFF $8000-$9FFF $A000-$BFFF $C000-$DFFF $E000-$FFFF 0 1 2 3 4 5 6 7 Memory Mapping Example Map external memory to: $4000-$5FFF

  16. First four bits of memory map: 0100 or 0101 Partial decoding: A[15-13] = 010 Address Decoding Why is E connected to E3 ? 74LS138 O0 E1 O1 010 E2 External Memory O2 E E3 O3 O4 A15 A2 O5 A14 A1 O6 O7 A13 A0 Address decoder design

  17. 74LS138: E3: active high enable => Decoding done when E clock is high I.e at second-half of E-clock cycle Goal: Enable (chip select) external memory with the output (O2) of decode at this time I.e. at second-half of E-clock cycle Decoding (contd) Decoded values available E

  18. 8KB SRAM HM6264A • Two chip enable signals: • CS1 is active low • CS2 is active high. • WE: write enable • (active low) • OE: output enable • (active low)

  19. Putting it together 74F138 PB7/A15 A2 PB6/A14 A1 O2 PB5/A13 A0 E E3 V E2 E1 DD 68HC11 CS2 CS1 74LS00 WE R/W 74LS04 PB4/A12 - A12-A0 PB0/A8 74F373 AS LE HM6264A O7-O0 AD7-AD0 D7-D0 OE OE I/O8 - I/O1

  20. Revisit: Bus Timing Diagram XTAL E R/W A15-A8 HI ADDR A7/D7-A0/D0 LO-ADDR DATA AS Second half of E-cycle

  21. During second-half of E-cycle CS1 asserted (from O2) E =1 during this time => R/W’ passed to WE’ Recall: (X.1)’ = X’ {NAND gate} In this case, X = (R/W’)’ {NOT gate} Latch output holds A0-A7 AD0-AD7 connected to I/O lines of SRAM Data sent back to port C if it is a READ Data sent from port C if it is a WRITE Putting it together (contd) Second half of E-cycle E

  22. Do Activity #2 Now • Due: End of Class Today. • RETAIN THE LAST PAGE(S) (#3 onwards)!! • For Next Class: • Read Chapter 4 of Huang • Review all material, identify your problem areas, and Bring your questions! • Next week’s studio: Catch up with experiments. Summarize reading of Chapter 4, Chapter 5 (sections 5.1-5.4), and Chapter 6 (6.1 – 6.7)

More Related