1 / 14

B-2179 副翼故障

IRR. B-2179 副翼故障. 维修动作 /Action ：. 系统概括和分析 /System Description AND Analysis ：. 系统概括和分析 /System Description AND Analysis ：. 系统概括和分析 /System Description AND Analysis ：. 系统概括和分析 /System Description AND Analysis ：. 系统概括和分析 /System Description AND Analysis ：.

quanda
Download Presentation

B-2179 副翼故障

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. IRR B-2179副翼故障

  2. 维修动作/Action：

  3. 系统概括和分析/System Description AND Analysis ：

  4. 系统概括和分析/System Description AND Analysis ：

  5. 系统概括和分析/System Description AND Analysis ：

  6. 系统概括和分析/System Description AND Analysis ：

  7. 系统概括和分析/System Description AND Analysis ：

  8. 系统概括和分析/System Description AND Analysis ：

  9. 初步调查Investigation • 本故障中心问题在于flap handle position transmitter的安装方法; • 安装flap handle position transmitter 的AMM 程序简要描述如下: • (1) Install the flap handle position transmitter as follows: • (2) Set the flap/slat handle to the UP/RET position.If removed, install the detent plug in the flap handle detent marked with a blue dot. • (3) Remove the safety tags and close these circuit breakers: • (4) Adjust the flap handle position transmitter. • (5) To keep the aircraft approved for CATEGORY IIIb status, do the FCC-1/FCC-2 flap position indication system category IIIb test. Make sure your CATEGORY IIIb maintenance program is used to complete this test. (Ref. FCC-1/FCC-2 FLAP POSITION INDICATION SYSTEM CATEGORY IIIB TEST, TASK 27-54-00-741-801)

  10. 初步调查Investigation • 调整flap handle position transmitter程序如下: • Adjust the flap handle position transmitter as follows: (Figure 532) (Figure 533) • (a) Put the flap/slat handle in the 0/EXT position. Make sure the flap handle transmitter position reads --0.90 ±0.50. • (b) If necessary, loosen bolt (BU) and adjust transmitter shaft (BV) until the flap handle transmitter position reads --0.90±0.50. Tighten bolt (BU). • (c) Put the flap/slat handle in the 28 detent. Make sure the flap handle transmitter position reads 28.40 ±0.50 • (d) If necessary adjust the pushrod (BR) as follows: • 1) Remove and discard the cotter pin (49). • 2) Remove the nut (50), the washer (51) and the bolt (52). • 3) Adjust the pushrod (BR) until the flap handle transmitter position reads 28.40 ±0.50. • 4) Install the bolt (52), the washer (51) and the nut (50). • 5) Safety the nut (50) with a cotter Pin (49).

  11. 初步调查Investigation

  12. 最终结论和措施（CLOSE） • 对本故障的排故总结如下: 1.根据FIM执行排故程序无法定位的故障,可参考SSM对故障现象进行分析后,迅速找到故障源. 2.操纵系统部件安装时,需逐个步骤按照手册进行调节和校装.应在工作前仔细准备,全盘了解每一步校装和调节的作用,避免不必要的弯路。 IRR会议确认关闭

  13. Thanks

More Related