642-980 Cisco Exam - Updated Questions

1. Cisco 642-980 Troubleshooting Cisco Data Center Unified Fabric (DCUFT) Demo Product To Buy Full Set of Exam Questions, Visit: http://www.test4direct.com/642-980.html

2. Question: 1 Which command would you use to find the AED of an extended VLAN in a dual-homed site of an OTV network? A. show otv aed on the AED B. show otv vlan on any edge devices in the site C. show otv vlan on the AED D. show otv aed on any edge devices in the site E. show otv site on any edge devices in the site Answer: C Explanation: Reference: http://www.cisco.com/en/US/docs/ios-xml/ios/wan_otv/configuration/xe-3s/wan-otv-confg.html Question: 2 Which statement is true regarding Cisco FabricPath? A. Cisco FabricPath cannot be disabled explicitly for a specific VDC. B. It is necessary to first install the Cisco FabricPath feature set in the default VDC. C. If the Cisco FabricPath feature is not installed, the fabric path keyword will be available in the feature-set command. D. Cisco FabricPath is only available on Cisco Nexus 7010 Switches with the Supervisor 2 engine. Answer: B Question: 3 Which statement is true regarding the admin VDC? A. Only the mgmt 0 interface is allocated to the admin VDC. B. All licensed features and feature sets must be enabled from the admin VDC. C. The admin VDC is a new feature in Cisco NX-OS version 6.0. D. Fabric extenders connected to the admin VDC must be statically pinned. E. The admin context can only be created on Supervisor 2/2E. F. All interfaces other than mgmt 0 are allocated to the default VDC. Answer: A Explanation: Reference: http://www.cisco.com/en/US/docs/switches/datacenter/sw/nx- os/virtual_device_context/configuration/guide/vdc_admin.html (guidelines and limitations for creating admin VDCs, second bullet, second sentence) Question: 4 Refer to the exhibit.

3. When suspending or deleting VSANs, which three statements are true? (Choose two.) A. You must wait 60 seconds after you enter the vsan suspend command before you enter another command. B. You can unsuspend only VSAN at a time. C. You can delete multiple VSANs as long as they are in the same domain. D. You can delete multiple VSANs as long as they are in the same zone. E. You must wait 120 seconds after you enter the vsan suspend command before you enter another command. Answer: A, B Explanation: Reference: http://docwiki.cisco.com/wiki/Cisco_MDS_SanOS_Troubleshooting_Guide_-- _Troubleshooting_VSANs,_Domains,_and_FSPF (initial troubleshooting checklist, see the note) Question: 5 Refer to the exhibit. A customer is having problems with NPV. Which of these is the cause of the problem? A. One external link must be up for server interface to be up. B. VLANs are misconfigured on the upstream ports. C. No server was requested or received by the FLOGI database. D. VSANs are misconfigured on the upstream ports E. Internal links are down and must be up for the server interface to be up Answer: D Question: 6

4. FHRP isolation between data center networks that are connected over an OTV network is a two-step process; the first prevents FHRP peering by filtering FHRP control packets across the overlay via a VLAN ACL. What is the second step? A. Disable the auto-population of the OTV MAC address table. B. Remove the FHRP VLAN from the OTV extend-vlan list. C. Apply a VLAN to a route map that is applied to the OTV routing process. D. Filter the FHRP MAC addresses that are being advertised by IS-IS. Answer: C Explanation: Reference: http://jeffostermiller.blogspot.com/2013/01/fhrp-isolation-with-otv.html Question: 7 Refer to the exhibit. When your customers have NPV problems, which three actions should you take? (Choose three.) A. Verify the status of the servers and external interfaces, using the show npv server status command. B. Ensure that the VLAN values are configured on both sides of the NPV core switch. C. For all the device links, ensure that the port mode on the NPV device is in Full_port mode. D. Ensure that the VSAN value that is configured on the device links is correct. E. Verify that the NPV core switch supports NPIV and that it is enabled. F. Verify that all ports are properly configured and connected. Answer: A, B, D Explanation: Reference: http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_3_x/troubleshooting/gu ide/ts_npv.pdf (page 9-2, initial troubleshooting checklist)

5. THANKS FOR TRYING THE DEMO OF OUR PRODUCT Visit Our Site to Purchase the Full Set of Actual 642-980 Exam Questions With Answers. 0TUhttp://www.test4direct.com/642-980.html We Also Provide Practice Exam Software That Simulates Real Exam Environment And Has Many Self-Assessment Features. Download Free Product Demo From: 0TUhttp://www.test4direct.com/642-980.htmlU0T Money Back Guarantee Check Out Our Customer Testimonials 0TUhttp://vimeo.com/102521226U0T