1 / 12

CEE 4606 - Capstone II Structural Engineering

CEE 4606 - Capstone II Structural Engineering. Lecture 10 – Masonry Shear Walls. Time for a Pop Quiz…. You should be familiar with… Differences between unreinforced and reinforced masonry MSJC code Components of masonry Properties/manufacturing of CMU Components of mortar.

Leo
Download Presentation

CEE 4606 - Capstone II Structural Engineering

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CEE 4606 - Capstone IIStructural Engineering Lecture 10 – Masonry Shear Walls

  2. Time for a Pop Quiz… You should be familiar with… • Differences between unreinforced and reinforced masonry • MSJC code • Components of masonry • Properties/manufacturing of CMU • Components of mortar

  3. Time for a Pop Quiz… You should be familiar with… • Types of mortar • Proportion and property specifications for mortar • Differences between mortar and grout • Types of reinforcement • Definition of f’m

  4. Time for a Pop Quiz… You should be familiar with… • Unit strength method vs. prism test method • Bond patterns for masonry • Gross, bedded, and net areas

  5. Shear Walls • Essentially act as vertical beams that resist gravity and in-plane lateral loads • Generally, shear walls must be checked for flexure and shear • Deflections (stiffness) may also be critical • difficult, consider both shear and flexural displacements • see text

  6. Unreinforced Shear Walls • Generally not very efficient • Limited tension capability • Work best with high axial loads • Basic Design Criteria: • Net Tensile Stress (Flexural – Axial) • Net Compressive Stress (Flexural + Axial) • Shear Stress

  7. Reinforced Shear Walls • Shear provisions are a function of the M/Vd ratio (essentially the h/d ratio) d H Flexure likely to control d H h h Shear likely to conrol V M V M

  8. Reinforced Shear Walls – Allowable Shear Stress Provisions (MSJC 2.3.5.2.2) • For walls with in-plane flexural reinforcement and no shear reinforcement • For walls with in-plane flexural reinforcement and shear reinforcement to resist the full shear

  9. Reinforced Shear Wall Example 80” • Fully grouted 8” (nominal) CMU wall • Type S mortar, f’m=3000 psi • The wall has no axial stress (ignore self-weight) • Vertical reinforcement is 2#8 at each end • Determine the maximum horizontal load H that can be applied to the wall. Avg. d=72” 6’-8” H (wind) 8’-0”

  10. Reinforced Shear Wall Example (continued) 80” • Assume wall has no horizontal shear reinforcement • Assume wall is underreinforced (technically must check) • M = AsFsjd (Assume j=0.9) • M = [(2)(.79)][(1.333)(24)](.9)(72) • M = 3275 in.-kips • H = M/h = 3275/96 = 34.1 kips • M/Vd = 96/72 =1.333 > 1.0 • Fv = (3000)1/2 = 55 psi > 35 psi • Fv = (4/3)(35) = 46.7 psi • Vmax = bdFv = (7.625)(72)(46.7) • H = 25.6 kips • Shear governs ---> H=25.6 kips Avg. d=72” 6’-8” H 8’-0”

  11. Reinforced Shear Wall Example (continued) 80” • Assume wall has sufficient horizontal steel to take full shear corresponding to flexural capacity • M/Vd = 96/72 =1.333 > 1.0 • Fv = 1.5(3000)1/2 = 82 psi > 75 psi • Vmax = Fvbd = [(4/3)(75)](7.625)(72) • = 54.9 kips • H = 34.1 kips < 54.9 OK • Av/s = Vmax/Fsd • = 34.1/[[(1.333)(24)](72)] • = 0.0148 sq. in. per inch • With 2 #4 bars, Av=0.40 in.2 • s = .40/.0148 = 27.0” • -----> Use 2#4 @ 24” spacing Avg. d=72” 6’-8” H 8’-0”

  12. Reinforced Shear Wall Example (continued) 80” • Summary • Only vertical reinforcement (2#8) • H = 25.6 kips (shear governs) • Vertical reinforcement (2#8) and horizontal reinforcement (2#4 @ 24”): • H = 34.1 kips Avg. d=72” 6’-8” H 8’-0”

More Related