1 / 23

CEE 4606 - Capstone II Structural Engineering

CEE 4606 - Capstone II Structural Engineering. Lecture 7 – Introduction to Foundation Design. Types of Footings. 1. Wall (strip) footings 2. Isolated footings 3. Combined footings 4. Mat (raft) footings ( not the same as a slab on grade ) 5. Pile cap. What did you learn last semester ?.

Download Presentation

CEE 4606 - Capstone II Structural Engineering

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CEE 4606 - Capstone IIStructural Engineering Lecture 7 – Introduction to Foundation Design

  2. Types of Footings 1. Wall (strip) footings 2. Isolated footings 3. Combined footings 4. Mat (raft) footings (not the same as a slab on grade) 5. Pile cap What did you learn last semester ?

  3. q, soil pressure Isolated Footings Column Footing (Square)

  4. Soil Pressures • At the ground surface we assume a uniform pressure distribution, as long as the load above is applied at the C.G. of the footing. • Does this reflect reality? • No, but it’s not a bad assumption • Factored loads • Simplifies calculations

  5. Non Uniform Soil Pressure • If the load is applied eccentrically with respect to the C.G. we assume a uniform variance in proportion to the moment

  6. qmin qmax Eccentric Loading Column Footing (Square)

  7. We have none of these! Allowable Soil Pressures • Structural engineers usually rely on geotechnical engineers for this information • Test borings • Load tests • Other experiments What can we do ?

  8. Maximum Allowable Soil Pressure(McCormac, 2001)

  9. Failure Types • Factor of safety against severe settlement ranges from 2.5 < F.S. < 3.0 • This limits bearing failure

  10. Two types of shear must be considered Beam shear, VU1 (One-way) L – length of footing d – distance to reinforcing a – column width Design of Square Isolated Footings d a d L

  11. Tributary area for one-way shear (hatched) a d L/2 – a/2 - d L / 2

  12. ACI 11.12.1.1 Similar to a beam Vc = 2 f’c bd Vs = 0 if there is no web reinforcing Vu<f(Vc +Vs) d a d L

  13. 2. Punching Shear (Two-way) • Critical section is d/2 from the column face • Vc is the smallest of 3 values • ACI Equations • 11-35 • 11-36 • 11-37 d/2 a d/2 L / 2

  14. where, bc = ratio of long side of the column to the short side b0 = perimeter of the critical section as = 40 for columns in the center of the footing 11-35 11-36 11-37 Punching Shear Note: 11-36 is wrong in the handout

  15. Designing for Bending Moments • Bending moment in a square footing is the same about both axes due to symmetry • What about column width, a? • Yes for a square column • No for a rectangular column • Generally use smallest value of a for analysis

  16. ACI 15.4 – Moments in footings • Location of critical sections • At the face of the column for concrete columns (our case) • Masonry wall • Steel column

  17. Stresses Under a Footing • P = vertical load (+ compression) • A = area of contact surface between the soil and the footing • I = moment of inertia of this area • M = moment about the centroidal axis • y = distance from the centroidal axis to the point where you want to calculate the stresses • This assumes that the loads are at or near the center of the footing

  18. P M y P/A My/I

  19. M = P e, where e = eccentricity Maximum e for this to be a valid analysis is when qmin = 0 Load must be within the kern ek = L/6 Limitations L/6 L/6 L

  20. References • Handout – Chapter 16 of Macgregor, J. G., Reinforced Concrete, Mechanics and Design, 3rd Edition, Prentice-Hall,1997. • ACI code • McCormac text, Chapter 11 • CONCAD, McCormac software

  21. Interim Assignment #3 • Link on the website to a personality indicator test • Fill it out, print out the summary sheet, put your name on it, and turn it in on Tuesday • We will be using the results, so take it seriously • If you haven’t paid your $40 course fee by Tuesday, we will deduct points off of your next group progress report Project managers are responsible

  22. Schedule for Progress Report #2 11:30 – 11:40 En Fuego Engineering 11:45 – 11:55 Ameriduras Ingeniros 12:00 – 12:10 Comma Engineers 12:15 – 12:25 Los Amigos de Amigos de Jesus 12:30 – 12:40 HyperStructo-CyberTronics Engineering and Associates Keep the setup and presentation portion < 10 minutes Work on improving animation and timing

  23. Computer Aided Structural Engineering • Homework #2 and #3 due Friday • Volunteers? • Who wants to be famous?

More Related