1 / 18

Adper  Prompt  Self-Etch Adhesive

An Alternative “No-Rinse” Sealant Placement Technique: 3M ESPE Adper  Prompt  Self-Etch Adhesive and 3M ESPE Clinpro  Sealant: This technique uses a self-etching dental adhesive to bond the sealant to the tooth. Adper  Prompt  Self-Etch Adhesive. Indications For Use:

Gabriel
Download Presentation

Adper  Prompt  Self-Etch Adhesive

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. An Alternative “No-Rinse” Sealant Placement Technique:3M ESPE Adper Prompt Self-Etch Adhesive and 3M ESPE Clinpro Sealant: This technique uses a self-etching dental adhesive to bond the sealant to the tooth.

  2. Adper Prompt Self-Etch Adhesive • Indications For Use: • Bonding light-cured composite • and compomer materials to • dentin and enamel • Desensitization of exposed root • surfaces • Bonding of light-cure resin • based pit and fissure sealants Unidose L-Pop delivery system

  3. Adper Prompt Self-Etch Adhesive and Clinpro Sealant American Journal of Dentistry 2003 Aug:16(4):249-51, Feigal RJ, Quelhas I. “Clinical trial of a self-etching adhesive for sealant application” • “From the standpoint of time savings, lowered complexity of treatment, and decreased challenge of patient management, the self-etching adhesive method of sealant application has a significant advantage over the traditional method”.

  4. Adper Prompt Self-Etch Adhesive and Clinpro SealantClinical Technique • Thoroughly clean the teeth to remove plaque and debris from the enamel surfaces and fissures • Do not use any cleaning medium that may contain fluoride or oils as it may affect the adhesion value. • Rinse thoroughly with water and dry • Isolate the tooth (e.g.with cotton rolls) • Dry the surface to be sealed • Activate the L-Pop

  5. Adper Prompt Self-Etch Adhesive: L-Pop Activation • Squeeze the material from the red reservoir into the yellow (middle) reservoir • The middle reservoir will expand indicating proper transfer of fluid

  6. Fold back the red reservoir until it meets the flat face of the yellow reservoir • Keep the red reservoir tightly squeezed while bending the package to prevent the material from flowing back • Squeeze the liquid from the yellow reservoir into the blue reservoir

  7. Apply a churning or spinning motion to the applicator for five seconds to mix the adhesive and fully coat the applicator tip

  8. A lightly yellow-tinted applicator tip indicates proper activation. If a yellow color is not obtained unfold the “L-Pop”, reactivate, and apply a spinning motion to the applicator for 5 seconds to mix the adhesive.

  9. Adper Prompt Self-Etch Adhesive Tip must be yellowindicating proper activation Clear tip indicates improper activation

  10. Apply adhesive onto the surface to be sealed; scrub for 15 seconds applying moderate finger pressure. Do not shorten this time. • Proper bonding will not occur if the solution is simply applied and dispersed.

  11. Use a gentle stream of air tothoroughly dry the adhesive to a thin film (approximately 10 seconds) • If the stream of air is too forceful, the adhesive will be blown off the tooth • The surface will appear glossy, but not moist • The tooth surface will not appear frosty as in the “traditional” technique

  12. Apply a light-cured sealant

  13. Light-cure the sealant and adhesive together with a halogen, LED or plasma light for the amount of time specified to cure the sealant

  14. Check sealant coverage and wipe clean

  15. Adper Prompt Self-Etch Adhesive and Clinpro SealantKey Technique Tips: • Activated L-Pop must be a deep golden yellow • The L-Pop can be activated up to 10 minutes before the procedure • Saves time to activate before bringing patient back to operatory • Adhesive must be scrubbed on the surface for a minimum of 15 seconds

  16. Key Technique Tips (continued) • Gentle, but thorough, drying step is critical • Purpose: evaporate the solvent (water) • Dry an inch or so away from the tooth surface • Adhesive will have a “waving” motion the first 10 seconds of drying • When “the wave” stops…water is evaporated • Tooth will not have a “frosty” appearance • Co-cure adhesive and sealant together for 20 seconds

  17. Benefits of Technique: • No rinsing involved (means no bitter taste, which can increase salivary flow and affect isolation) • Adper Prompt pH low (.8) and will etch an uncut enamel surface • Few other SE adhesives have this ability • Sealant is actually being bonded to the tooth (same concept as bonding a composite)

  18. Benefits of Technique: • Less microleakage compared to the traditional technique • Means less chance of recurrent decay/better retention • Decreased challenge of patient management • Saves time compared to the traditional technique

More Related