1 / 23

Chapter 9: Circuit Switching

Chapter 9: Circuit Switching. Switching Networks Circuit-Switching Networks Circuit-Switching Concept Space-Division Switching Time-Division Switching Routing in Circuit-Switching Networks Control Signaling SS7. Switching Networks.

ivana-avila
Download Presentation

Chapter 9: Circuit Switching

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 9: Circuit Switching • Switching Networks • Circuit-Switching Networks • Circuit-Switching Concept • Space-Division Switching • Time-Division Switching • Routing in Circuit-Switching Networks • Control Signaling • SS7

  2. Switching Networks • Long distance transmission is typically done over a network of switched nodes • Nodes not concerned with content of data • End devices are stations: Computer, terminal, phone, etc. End device node

  3. Switching Networks (Con’t) • A collection of nodes (switches) and connections is a communications network • Data routed by being switched from node to node • Nodes may connect to other nodes (switches) only, or to stations (hosts)and other nodes • Node to node links usually multiplexed (TDM &FDM) • Network is usually partially connected • Some redundant connections are desirable for reliability • Two different switching technologies • Circuit switching • Packet switching

  4. Circuit Switching & features • Dedicated communication path between two stations • Three phases: Establish; Transfer; Disconnect • Must have switching capacity and channel capacity to establish connection • Must have intelligence to work out routing • Inefficient • Channel capacity dedicated for duration of connection • If no data, capacity wasted • Set up (connection) takes time • Once connected, transfer is transparent, no delay -> • Developed for voice traffic (phone)

  5. Telecomm. Networks & Components • Subscriber: Devices attached to network • Local Loop: Subscriber loop -> Connection to network • Exchange: Switching centers; end office supports subscribers • Trunks (Multiplexed): Branches between exchanges

  6. Circuit Switch Concepts & Elements • Digital Switch • Provide transparent signal path between devices • Network Interface • Control Unit • Establish connections • Generally on demand • Handle and acknowledge requests • Determine if destination is free • construct path • Maintain connection • Disconnect

  7. Digital Switch: Blocking vs. Non-blocking • Blocking • A network is unable to connect end stations because all paths are in use • In blocking network this is possible • Used on voice systems • Short duration calls • Non-blocking • Permits all stations to connect (in pairs) at once • Used for some data connections • Switching Techniques • Space-Division Switching • Time-Division Switching

  8. Flat Crossbar Switch: Example of space-division Switch • Separate physical paths for signal for one another • E.g., Crossbar switch • When a request comes in from an incoming line for an outgoing line, the corresponding crosspoint is closed to enable information to flow from the input to the output • The connection requests are neverblocked due to the lack of connectivity resource (crosspoint), but a busy outgoing line rejects a connection request • The complexity of the crossbar switch is measured by the number of crosspoints (N2)

  9. kxn nxk N/n x N/n 1 1 1 kxn nxk N inputs 2 2 N outputs N/n x N/n kxn nxk 2 3 3          kxn nxk N/n N/n N/n x N/n k Multistage Space-Division Switch • Reduced number of crosspoints:2(N/n)nk + k (N/n)2 crosspoints • More than one path through network->Increased reliability • More complex control • May be blocking: can be solved by increasing # of intermediate switch

  10. Three Stage Switch

  11. Time Division Switching • All digital switching technology is base on the use of STDM • During a time slot, data are switched from the enabled input line to the enabled output line, # of time slot = # of devices • The data rate on the controller must be high enough: e.g. 100 device @ 19.2kbps, controller date rate at 1.92Mbps • Partition low speed bit stream into pieces that share higher speed stream • e.g. TDM bus switching • based on synchronous time division multiplexing • Each station connects through controlled gates to high speedbus

  12. Routing • Many connections will need paths through more than one switch • Need to find a route • Efficiency • Resilience • Static routing uses the same approach all the time • Dynamic routing allows for changes in routing depending on traffic

  13. Alternate Routing: an example routing approach • Possible routes between end offices predefined • Originating switch selects appropriate route • Routes listed in preference order • Different sets of routes may be used at different times • Can be implemented statically or dynamically

  14. Alternate Routing Diagram

  15. Control Signaling Functions • Audible communication with subscriber • Transmission of dialed number • Call can not be completed indication • Call ended indication • Signal to ring phone • Billing info • Equipment and trunk status info • Diagnostic info

  16. Control Signal Sequences

  17. Location of Signaling • Subscriber to network • Depends on subscriber device and switch • Within network • Management of subscriber calls and network • more complex • Mapping is needed between the two signaling techniques @ the local switching office

  18. InChannel Signaling: an traditional signaling approach • Use same channel for signaling and call • Requires no additional transmission facilities • Inband • Uses same frequencies as voice signal • Can go anywhere a voice signal can • Impossible to set up a call on a faulty speech path • Out of band • Voice signals do not use full 4kHz bandwidth • Narrow signal band within 4kHz used for control • Can be sent whether or not voice signals are present • Need extra electronics • Slower signal rate (narrow bandwidth)

  19. Drawbacks of InChannel Signaling • Limited control signaling transfer rate • Inband signaling: when there is no voice data • Out-band signaling: a very narrow bandwidth is for signaling • Delay between entering address (dialing) and connection • Overcome by use of common channel signaling

  20. Common vs. InChannel Signaling

  21. Common Channel Signaling • Control signals carried over paths independent of voice channel • One control signal channel can carry signals for a number of subscriber channels • Associated Mode • Common channel closely tracks interswitch trunks • Disassociated Mode • Additional nodes (signal transfer points) • Effectively two separate networks

  22. Signaling System Number 7 • SS7: a real world Common channel signaling scheme • Used in ISDN (Integrated Service Digital Network) • Optimized for 64k digital channel network • Functionalities: Call control, remote control, management and maintenance • Reliable means of transfer of info in sequence • Suitable to operate over analog and below 64k • Suitable to point-to-point terrestrial and satellite links

  23. SS7 Signaling Network Elements • Signaling point (SP) • Any point in the network capable of handling SS7 control message • Signal transfer point (STP) • A signaling point capable of routing control messages • Control plane • Responsible for establishing and managing connections • Information plane • Once a connection is set up, info is transferred in the information plane

More Related