1 / 20

AC-SSC-1 Installation and operation manual

AC-SSC-1 Installation and operation manual.

aysha
Download Presentation

AC-SSC-1 Installation and operation manual

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. AC-SSC-1 Installation and operation manual

  2. The SpacePak AC-SSC-1 is an interface module that allows communication between a wide variety of commercially available thermostats, air handlers, control systems, and the SCM-036 & SCM-060 reverse cycle chillers. The AC-SCC-1 is used to communicate between a single air handler and one chiller. • Description: • The AC-SSC-1 consists of two electromechanical relays mounted inside metal enclosure that can be located at any indoor location. The AC-SCC-1 operates on 24VDC signals from the air handler or thermostat circuit, and does not require any additional power supply. The output signal consists of two “dry” contacts, one to enable the chiller and one to determine heating or cooling operation. These switch to open or close the low voltage circuit supplied by the chiller • Installation: Before beginning,ensure all power is removedfrom the chiller, either at a breaker or disconnect. Mounting and wiring must be accomplished by a qualified technician who is responsible for compliance with all local codes and good practices. • Mount the AC-SCC-1 in a dry indoor location that provides easy wiring access from the air handler, and to the outside chiller. The enclosure must be attached securely to a wall or other fixed structure. • Determine whether the thermostat wiring will be connected at the air handler, or at the AC-SCC-1 module. The AC-SCC-1 does not perform any control function between the thermostat and the air handler, but depending upon the physical location of these components, can provide a convenient junction point between the two. If the thermostat is wired directly to the air handler, and the air handler alone is wired to the interface module, only the Y, O/B, and C connections need to be made. • Pass the control wires from the air handler/thermostat through the grommet at the lower left of the enclosure, and install them as indicated to the terminal strip at the bottom of the panel. • Install a minimum four conductor, single strand 22 AWG copper, thermostat wire from the interface module, to the chiller. • Pass the wire through the grommet at the upper right of the enclosure, and connect one each conductor to the four terminal points marked 7, 8 & 43, 44 at the top of the panel. Note the color of the individual wires as these must be connected to the same numbered terminals in the chiller. • Using the square bit key supplied with the chiller, remove the access plate on the chiller. • At the chiller, pass the control/thermostat wire through one of the grommets in the chiller enclosure not already occupied by the chiller power supply wiring. Take care to route

  3. spring. This will then free the end of the blue jumper which can be gently pulled out of the wire slot. • Remove jumper, if present • Wire Slot • Release Slot • While still depressing the spring, install the wires from terminals 7 & 8 into the same wire slots. • Repeat above steps 8 & 9 at terminals 43 & 44. • Ensure all wire are routed neatly and clear of the access opening, and replace the access panel using the square bit key. • Testing: • When all wire connections have been completed, turn on power to the chiller. • Set the indoor thermostat, or other control device, to call for heating. (this assumes that the glycol/water solution in the chiller is lower than the heating setpoint. If the temperature is higher, proceed with step 7, below. • Observe that the thermostat, or air handler, sends a signal to call for heating. (depending on the specific thermostat or air handler setpoints, this may pause for of up to two minutes before reacting) • When the call is sent, wire Y1 will energize the left-most relay in the interface module, producing an audible “click”, and the contacts will close completing the circuit between terminals 43 and 44. • The chiller will begin by flashing the Pump symbol for one to two minutes while the control undergoes a self-test. The symbol will then become solid and the pump will begin to circulate. The heating symbol will then begin to flash, again for one to two minutes, and then become solid. At this time, the compressor(s) will engage and the system will begin heating. • Lower the thermostat to remove the call for heating, and allow the chiller to complete its shutdown cycle, running for two to three minutes. • When the chiller has shut down and the pump stopped circulating, lower the thermostat to initiate a call for cooling. Again, this may pause for up to two minutes. • When the call for cooling is sent, the wire Y1 will again energize the left-most relay, and wire O/B will energize the right-most relay, producing an audible “click” and opening the circuit between wires 7 and 8.

  4. The chiller start sequence will be the same, except that now the cooling symbol will display. • Heating Symbol • Chiller Display • Cooling Symbol • Pump Symbol • Control Logic: • The default configuration, and above description, assume the following. • The thermostat and/or air handler energizes the O/B connection in cooling, and de-energizes it in heating. • The chiller operates in cooling when circuit 7 & 8 is open, and heating when circuit 7 & 8 is closed. • If either of these conditions is not true, causing the chiller to function opposite to the description above, the operation of the interface module can be reversed by simply relocating wire 7, at the right-most relay, from the NC terminal to the NO terminal.

  5. AC-EIH-3 Installation and operation manual • The SpacePak AC-EIH-3 is a kit that will provide supplemental heat to the SCM-036 & SCM-060 chillers in two different modes. During periods of non-operation, the kit will provide freeze protection for the glycol solution in the system, and in heating mode it will provide supplemental heating during extreme high load or low temperature conditions.

  6. (INSERT ELECTRIC HEATER IOM)

More Related